guys, here my problem :
I have unlocked and rooted my xPeria p, everything is OK.
(my fool...) did not notice all suggest not to OTA update after unlock my device, I did an update via OTA and my XPeria P ruin....
i have try to fix it with flash tool but it can't enter in flash mode.
i have try enter flashmode by holding "Volume down" button while inserting the USB cable into the phone. still didn't work
My PC companion don't recognize either
please help.................
search before posting, http://forum.xda-developers.com/showthread.php?t=1712075
Sir a search for your device forum would best serve you and better assist you, Thank You and btw thank the user above me for providing you with a link.
Related
For days I was stuck on a problem, which was that I could not connect my device to the PC by via Flashmode. For this reason could not flash ftf firmware and this had me desperate.
After much reading and found nothing, try something and found the solution to this problem.
To connect the Xperia L C2105 after unlock the bootloader no longer works with the metod (button volume -). In return must be connected thoroughly pressing camera button.
Maybe for some this and knew it was something, but when making my question gave me no answer and I want to make this contribution.
If my thread is not corresponding in this section, moderator thank move it to where appropriate.
Good luck.
I know there are probably lots of threads about this, but I couldn't find one about E3 since it's a relatively new phone, but to point now
So I tried to update my Xperia E3 to it's latest firmware via the Sony pc companion(it was the only option) and during the update ,once it was downloaded it prompted to connect the phone through the USB cable, once done it began installing the update but when it was like at 80-85% it showed an error saying that internet connection isn't available and gave two options to either retry or cancel, now the internet was just working fine, I checked google, Youtube everything and it was working, but every time I hit retry it gave the same option ,so eventually I canceled the update,
Now the phone was switched off so I tried switching it on and it just froze at the sony boot logo screen, restarting with power button+volume up only restarts it to the same situation(stuck at logo screen), I did look up for a solution but couldn't find one that fit,
Of course I did switch it off using the off button at the back of phone(under the back cover), and I know about Sony Update service but that's no longer supported(it required the phone in off state), pc companion can't detect an off phone and when it does it starts phone to boot frozen screen and fails at detect step, another thing I found was a custom tool(possibly just SUS) that could flash a firmware in an off phone but however there is no firmware available for my version, since I live in India, so there's that , any help is appreciated,
A few things:
-The battery was at 91% when update started
-There was no root attempt etc made on phone, it was complete stock
-I did update the firmware once earlier but just from the phone it was a 2 mp update, no pc
-When I started this update there was already a 29 mb something update available without pc, and that's pretty much all, like I said any help is appreciated
Don't worry buddy, your phone doesn't die yet. Actually, PC Companion (PCC) has repair phone/tablet function.
Open PCC, click Start button in Support Zone, then continue to click Start button under Phone/Tablet Software Update and you will see "Repair your phone/tablet". Just follow its instruction. remember using the hard reset button under the back cover to turn off the device first and don't turn it on.
Anyway, what is your model? d22xx? i can't provide the firmware unless I know exactly the model.
It worked
Benjoy Ericsson said:
Don't worry buddy, your phone doesn't die yet. Actually, PC Companion (PCC) has repair phone/tablet function.
Open PCC, click Start button in Support Zone, then continue to click Start button under Phone/Tablet Software Update and you will see "Repair your phone/tablet". Just follow its instruction. remember using the hard reset button under the back cover to turn off the device first and don't turn it on.
Anyway, what is your model? d22xx? i can't provide the firmware unless I know exactly the model.
Click to expand...
Click to collapse
Thanks man, it worked, the phone is good and running again.
Benjoy Ericsson said:
Don't worry buddy, your phone doesn't die yet. Actually, PC Companion (PCC) has repair phone/tablet function.
Open PCC, click Start button in Support Zone, then continue to click Start button under Phone/Tablet Software Update and you will see "Repair your phone/tablet". Just follow its instruction. remember using the hard reset button under the back cover to turn off the device first and don't turn it on.
Anyway, what is your model? d22xx? i can't provide the firmware unless I know exactly the model.
Click to expand...
Click to collapse
Hello, my device is D2212 and I have similar problem.
I've rooted and unlocked bootloader using this method from XDA forum to root Xperia E3. However after unlocking bootloader and root my device my PC and my notebook doesn't recognize my device to transfer data or access data of cellphone. It keeps in charging mode.
Today it was really weird and lagging way too much so I tried to reset to factory setting. After that my device does not start android it keep stuck on blue screen right after display of Xperia and android.
I tried this method you suggested of PC Companion but it does not work since PC does not recognize my device anymore since rooting.
I need help here, please.
O just bought this device last week.
Thanks in advance.
Cristy0505 said:
Hello, my device is D2212 and I have similar problem.
I've rooted and unlocked bootloader using this method from XDA forum to root Xperia E3. However after unlocking bottloader and root my device my PC and my notebook doesn't recognize my device to transfer data or access data of cellphone. It keeps in charging mode.
Today it was really weird and lagging way too much so I tried to reset to factory setting. After that my device does not start android it keep stuck on blue screen right after display of Xperia and android.
I tried this method you suggested of PC Companion but it does not work since PC does not recognize my device anymore since rooting.
I need help here, please.
O just bought this device last week.
Thanks in advance.
Click to expand...
Click to collapse
Flash the firmware again using flashtool.
adrianocolvero said:
Flash the firmware again using flashtool.
Click to expand...
Click to collapse
Hi, thank you for your kind support.
Do you mean which part of this tutorial? http : // forum.xda-developers.com/xperia-e3/general/root-e3-t2964845
First "HOW TO UNLOCK YOUR BOOTLOADER!" or second "NOW HOW TO FLASH THE KERNEL AND APPLY THE ROOT!"?
Best regards!
Cristy0505 said:
Hi, thank you for your kind support.
Do you mean which part of this tutorial? http : // forum.xda-developers.com/xperia-e3/general/root-e3-t2964845
First "HOW TO UNLOCK YOUR BOOTLOADER!" or second "NOW HOW TO FLASH THE KERNEL AND APPLY THE ROOT!"?
Best regards!
Click to expand...
Click to collapse
Use this tutorial:
http://forum.xda-developers.com/xperia-z/general/tutorial-how-to-flash-stock-roms-t2240614
With this firmware:
http://forum.xda-developers.com/xperia-e3/general/firmware-18-4-b-2-14-rool-xperia-e3-t2939699
adrianocolvero said:
Use this tutorial:
http://forum.xda-developers.com/xperia-z/general/tutorial-how-to-flash-stock-roms-t2240614
With this firmware:
http://forum.xda-developers.com/xperia-e3/general/firmware-18-4-b-2-14-rool-xperia-e3-t2939699
Click to expand...
Click to collapse
Thank you very much, sir!
hai guys i have a xperia e3 dual d2212 i'm not sure whether it's rooted or unlocked bootloader it stucks on logo screen i try to flash it using flash tool but it says
ERROR drivers needed to be installed for connected device
ERROR you can find them in the drivers folder of flashtool
but i searched there there no devices mentioning e3 only e is available
in this condition should i flash or there is any other way please give me a solution
Hello I have a Sony experia e3 and it is giving me a problem. When I'm trying to start my phone it is booting and gets off by itself and again restarts...and this is going on and on. So please can you help me or give me a suggestion about how to fix it.
Please please please help for which I may remain ever greatful to you
Basically what the title says, i've been looking up on google and on the forum but i just can't find anything.
I have an Xperia J and everytime i connect my phone via USB (i want to use flashtool) holding the volume down the led goes green and flashtool tells me that the device has been connected in flash mode. BUT, after a couple of seconds the SONY logo shows on the screen and it does a sort of "reboot" and the led turns orange (like when i plug the cellphone w/o flash mode). I already unlocked the bootloader, i checked the drivers, but i have no idea of what to do.
Sorry for my bad english, but i need help q.q
Thanks guys!
XDA Visitor said:
Basically what the title says, i've been looking up on google and on the forum but i just can't find anything.
I have an Xperia J and everytime i connect my phone via USB (i want to use flashtool) holding the volume down the led goes green and flashtool tells me that the device has been connected in flash mode. BUT, after a couple of seconds the SONY logo shows on the screen and it does a sort of "reboot" and the led turns orange (like when i plug the cellphone w/o flash mode). I already unlocked the bootloader, i checked the drivers, but i have no idea of what to do.
Sorry for my bad english, but i need help q.q
Thanks guys!
Click to expand...
Click to collapse
Have you tried a different USB cable, another USB port, another PC?
And check the Frequently Asked Questions (FAQ) Miro, Tipo (Dual) and J.
If it doesn't help either, please register on xda and post in the Xperia Miro, Tipo (Dual), J, E Q&A, Help & Troubleshooting forum.
Good luck !
It_ler said:
Have you tried a different USB cable, another USB port, another PC?
And check the Frequently Asked Questions (FAQ) Miro, Tipo (Dual) and J.
If it doesn't help either, please register on xda and post in the Xperia Miro, Tipo (Dual), J, E Q&A, Help & Troubleshooting forum.
Good luck !
Click to expand...
Click to collapse
Hey it's me, I registered, anyway I tried every single port of my PC (usb 2.0 and also 3.0), i tried some other USB cable (from samsung and LG) but I didnt try it on another pc, i dont have it, so my question is: can I use a Virtual Machine?
Slark said:
I had this issue with an xperia s
This is an incompatibility issue with a windows 7/8 and The phone.
Try the same procedure with windows XP it should work
Greets
Click to expand...
Click to collapse
Same as before, can I use a virtual machine to do that?
YungMvtt said:
Hey it's me, I registered, anyway I tried every single port of my PC (usb 2.0 and also 3.0), i tried some other USB cable (from samsung and LG) but I didnt try it on another pc, i dont have it, so my question is: can I use a Virtual Machine?
Same as before, can I use a virtual machine to do that?
Click to expand...
Click to collapse
You can try it in a virtual machine ... but IDK if it will work.
Best to ask in the Q&A thread of your device I linked in my previous post.
Just a reminder: XDA Assist is not a discussion forum. It's just to point to the best place for help
Thanks for your understanding. Thread closed.
I tried to put AOSP 5.1 from FXP in my phone, and my cellphone bricked. It wont turn on, it keeps the Sony Logo 2 seconds. It haven't connection with flashtool. Please Help me.
Hi. Can you give me more information what you did exactly step by step. So maybe i can help you. My E3 was bricked too. I found a solution. But i need more information.
Flash stock rom it'll unbrick it
#4
Thank you answer back! I did exactly the following:
The model is my Xperia E3 D2212 dual sim.
- Unlocked the bootloader, :laugh:
- CWM installed a custom recovery, :laugh:
- I reinstalled the original rom, :laugh:
- I made a backup of the entire system using CWM.
And everything went super normal way, without complications.
The mistake was when he wanted to installing a custom ROM called "AOSP_L_MR1_150718_flamingo" because I found out later that he had not read that it was for ANOTHER XPERIA as follow the you tube tutorial . The ROM's for another Xperia, if I remember correctly.
After doing the installation process of the new AOSP ROM, the phone is less than a minute on the logo of SONY XPERIA down with, looped, can not enter the bootloader, and no longer recognizes the PC. I can not recognize it at FlashTool. I think that's all. :crying:
I greatly appreciate your attention.
I ended up editing this text in the google translator, then I'm sorry, if you are not very good.
Thank you
Matteus Maximo Felisberto said:
I tried to put AOSP 5.1 from FXP in my phone, and my cellphone bricked. It wont turn on, it keeps the Sony Logo 2 seconds. It haven't connection with flashtool. Please Help me.
Click to expand...
Click to collapse
Someone can help me please?
nibeal said:
Hi. Can you give me more information what you did exactly step by step. So maybe i can help you. My E3 was bricked too. I found a solution. But i need more information.
Click to expand...
Click to collapse
Could you help me? I can not make the pc recognize him ... He barely turns on and off since. The PC Companion software tells recognize it, but when you are installing the software says "it is not possible for this phone is changed." I can not scessar the bootloader does not give time and it shuts down.
Thanks, my error was with the fastboot driver and adb in flashtool. The Windows drivers wasn't been recognized, I've to install the drivers, all of they. After this, I Flashed the Stcok ROM, installed SuperSU and Restored the backup, everything works fine and fluid now. Thanks, anyway, for encouraging me.
I flashed my D2203 back to factory rom yesterday using Flashtool (flashtool.net/downloads.php) on Windows 7 PC.
How did I do it:
1) Install flashtool
2) Install Flashtool-drivers.exe from flashtool subfolder /drivers and select flashmode and fastboot drivers.
3) Run Flashtool and open XperiFirm (letters XF on logo)
4) Select Xperia E3 Flamingo -> proper D22** you have -> Market -> and select latest release below PayPal logo
5) Press "Download" and wait for download and unpacking
6) Switch off phone (if power on/off button does not respond then open back cover and push "OFF" by using pen)
7) Press and hold volume down button and connect phone to PC using original USB cable
8) Using Flashmode flash device
Hi everyone, im trying to downgrade my android to nougat and otw bricked the device. Im using flashtool to do this and the bad part is I forgot to turn on usb debug before. I tried using Xperia companion to fix this but and error came out saying "failure to get device info" kinda like. So is there any other way i can do this.
My phone is SOV35 au model with unlock bootloader not allowed but i flashed it to G8231 to unlock the sim. Any insight would really help on this. Thank you
First charge the phone.
Keep it switched off.
Here are the links
https://forum.xda-developers.com/xzs/how-to/oreo-xperia-xzs-g8232customized-ru1308-t3732394
There is a single sim.variant in he link too. Use Flashtool to flash these.
Start flashtool. Select appropriate firmware.
Click start flashing and then when it prompts.
Plug the cable in phone first and then pressing volume down plug it into PC. Wait until you see the green light in phone.
This should work.