Related
I literally had the worst combination of events take place the other day:
So, I was running Firefly 3.0, and I planned on replacing it with a gingerbread ROM, (since my apps weren't saving data, for some reason), and I started to notice that my unlock button was starting to hang a bit. I thought this was just another side effect from Firefly 3.0 acting weird.
So, I boot to download, and flash the CM7 kernel with CWM 3.0 on it, and it passes.
The next step is to navigate around in CWM to install the ROM file before you can boot up. But, the power/lock button still doesn't work! So I'm stuck in CWM 3.0, unable to boot correctly. The touch buttons don't work like they do in CWM 2.x, so I'm... stuck.
So, I call Samsung, and I'm having a replacement sent to me within the week, since I can't even power on/off my phone (if it wasn't for CM7's auto-boot when you put the battery in)
So, already having adb installed on my Linux boot, I jump over there to send the adb reboot download command. All this does is reboot the phone "normally"!
What are my options here? I've already copied everything off my phone with adb, and I'm not afraid to use terminal commands to flash something usable just to get it back to stock before I send it back.
*cough*JIG * COUGH*
Sent from my SAMSUNG-SGH-I897 using XDA App
Would that work with CWM 3.0/CM7 Kernel? I've always had weird issues with plugging things in and it just booting up, even when my power button worked.
The jig should work...the only thing that would cause the cm7 kernel to boot when plugged in is if it was off and you were only trying to charge it. The jig just redirects some power into pin 4 telling the bootloader to initiate download protocol...kinda the same way your phone knows when its hooked to a mountable usb port and when its charging out of the wall or something.
similar issue
I recently attempted a flash of fantasy II (2.3.5) captivate, and i got the bootload, and kernel installed and then installed the stock 2.3.5 rom to flash fantasy II over. . . . well after getting the stock rom, i found it had what i wanted, so i was going to stick with that.
i noticed about ten minutes after getting that rom, that my lock button was not working, and the phone would auto boot, i would pull the battery and put it back in and BOOM at&t boot screen right away, not one button pushed, I have bricked and unbricked my phone since then, and i am now simply running 2.1 stock, however; the dang lock button still does not respond at all, and it will auto boot still, is this the kernel or the bootloader? I know its not the rom now . . . . Please help this is awful!
and if you have a solution that i can download please post it!
First off, I know I'm a new member, and I did watch the video, I've been searching the forum for days now trying to find someone with the exact some problem as me but I've come to the conclusion I must be special as I haven't seen this problem else where. Lucky me...
Let me start off with some information about the phone.
Carrier: Vodafone AU (says XSE on the recovery screen)
Baseband Version: I9020XXKI1
Bootloader Version: I9020XXKL1
HW Version: Rev 52
Model: Nexus S i9023
Lock State: Unlocked
Primary computer: iMac
Fairly certain I have USB debugging turned off :\
I rooted and unlocked the phone and was running the latest CyberGR mod ROM and the latest AirKernel kernel. The phone was running brilliantly, not a problem in the world, very smooth, very fast, excellent battery life, I loved it. Only thing I didn't like was how the keyboard became unresponsive at times. For that reason, I think I'll be switching to the Bugless Beast ROM and thalmus kernel when (if) I get this phone fixed.
So a few days ago, the power button on my Nexus S stuffed up and wouldn't work anymore. Completely unresponsive. I couldn't lock/unlock my phone using the power button. I had to either connect/disconnect it from the USB or turn it on/off by taking the battery out to be able to use it. Needless to say, this got very tedious very quickly and I decided to unroot it and send it back to Samsung.
I looked into how to unroot and came across the Odin app and decided that I'd use that to unroot. (noob error on my behalf, I realise now) Regardless of what I'd read, Odin doesn't work on a Nexus S apparently and although I didn't flash to stock, my phone became significantly less useable, half the time it wouldn't respond to anything I did on it. I tried to boot into CWM and although I was able to do so, it was useless as my power button wasn't working.
At this stage, I took out the battery, put it back in and the phone booted up again. I didn't press the power button, it just booted up straight away. I took it out again and held the volume up button on the side and this time, I didn't get put into the CWM menu, but the normal Android recovery menu. I went to press the volume up and down buttons but nothing worked. Power button is still unresponsive.
When I don't boot into recovery, it goes past the Google screen with the unlocked lock on the bottom of it, and goes to a screen where it says "Android" in a metallic style (I disable the boot animation logo in CyberGR mod so I was used to this screen) and it just hung on there, it never booted up past that screen.
Every time I tried to use fastboot -w to wipe the phone, or oem lock or anything, I would just get < waiting for device >
I plugged it into my Windows 7 laptop, tried the one_click_stock app and got the message that my phone has no boot.img. I then googled problems regarding the boot.img and no one really had any solutions that helped me out.
The SDK won't recognise my phone is there, but the sound pops up on Windows saying a device has been connected and disconnected but it never shows up.
Is it bricked or unfixable? Clearly warranty is void, not sure if I should just take it into Vodafone and ask for a new phone (as its still within warranty period, hence why I wanted to lock it and flash a stock ROM).
Very sorry for the lengthy post, I know I was meant to be brief but I thought the more information I could give, the better chance there would be for anyone to help me out. Thanks.
Make the root of your phone with any application in the market and install the recovery ClockworkMod touch with Rom manager premium or Rom toolbox Pro. Restart recovery using Rom manager or Rom toolbox and do a full cleaning on the phone. Wipe only data and cache.
Now, select from mount and storage mount USB storage and copy over to your i9020 storage any rom ( try using the cm9 ). If the installation is successful restart, if not try some other roms. More than that I do not know how to help.
P.s.: In theory it should go smoothly, otherwise I do not assume any liability for further damage to the phone ... Good luck!
Did you know you can operate cwm using the capacitive search button instead of the power button?
Alfaneo said:
Make the root of your phone with any application in the market and install the recovery ClockworkMod touch with Rom manager premium or Rom toolbox Pro. Restart recovery using Rom manager or Rom toolbox and do a full cleaning on the phone. Wipe only data and cache.
Now, select from mount and storage mount USB storage and copy over to your i9020 storage any rom ( try using the cm9 ). If the installation is successful restart, if not try some other roms. More than that I do not know how to help.
P.s.: In theory it should go smoothly, otherwise I do not assume any liability for further damage to the phone ... Good luck!
Click to expand...
Click to collapse
Thanks for the reply, I can't actually boot into the phone or get to any market place or any screen that could make the phone useable at all, it just sits on the CyberGR android screen for when you disable the boot animation.
bedalus said:
Did you know you can operate cwm using the capacitive search button instead of the power button?
Click to expand...
Click to collapse
I was pressing the search button (the volume buttons were working when I could boot into CWM) and the text just disappeared off the screen and just showed the logo. I can no longer boot into CWM.
I've installed Ubuntu and I'm going to try running the unrbickable java app that a user on here created, hopefully that may work.
Ok guys, new to the forums but this problem has had me fully occupied for the last 6 hours and I feel like I have tried everything. I had cm9 alpha 12, and went to flash TrickDroid v5.0, something happened and I'm currently stuck in some wierd bootloop/soft brick. I had access to CWM but my SD card wouldn't mount and my adb push attempts didn't do anything, for reasons I don't know why. My phone would start up into the wierd trickdroid bootup and last for like 30 minutes. I tried the solution of another thread on how to fix a bootloop/ softbrick, but now I dont have any CWM access and I can only access the bootloader or the endless bootup screen. I tried using the all in one tool to flash the CWM again but it just restarts it and puts it back into the bootup, and when i restart to go to bootloader to acess the recovery, it goes back to bootup. Every solution I try makes my problem worse, and to top it off I cant turn my phone off and keep it off because it will just start back up. Thanks.
Edit: Problem fixed. Downloaded the original all in 1 tool for htc one s, plugged phone into comp went to fastboot and with the tool flashed the phones stock recovery. I reset to factory defaults and cleared storage with it from the bootloader. After that, I flashed clockwork mod recovery again and my SD card was able to be mounted and accepted files from my adb push, and I reflashed cyanogenmod. Wuzzah!
milesmarrero said:
Ok guys, new to the forums but this problem has had me fully occupied for the last 6 hours and I feel like I have tried everything. I had cm9 alpha 12, and went to flash TrickDroid v5.0, something happened and I'm currently stuck in some wierd bootloop/soft brick. I had access to CWM but my SD card wouldn't mount and my adb push attempts didn't do anything, for reasons I don't know why. My phone would start up into the wierd trickdroid bootup and last for like 30 minutes. I tried the solution of another thread on how to fix a bootloop/ softbrick, but now I dont have any CWM access and I can only access the bootloader or the endless bootup screen. I tried using the all in one tool to flash the CWM again but it just restarts it and puts it back into the bootup, and when i restart to go to bootloader to acess the recovery, it goes back to bootup. Every solution I try makes my problem worse, and to top it off I cant turn my phone off and keep it off because it will just start back up. Thanks.
Click to expand...
Click to collapse
lol, meant to "quote" not "thanks".
Can you fastboot a new recovery?
Did you do a full wipe coming from CM9 to TrickDroid
Well I can't access the phone from usb on my computer (still takes charge though), so I don't think I can flash a recovery thru fastboot (I'm not too experienced though). From cm9, I wiped all and flashed trickdroid + tweak set, then it just stat their at home screen. CMW being lost occurred later.
Im in the same situation rght now. I have trickdroid and I went into my tweaks to set them back to their original setup...so removing all of the options I chose before when I used the tweaks for the first time. When I rebooted my phone it just hangs on the HTC screen. I can get into recovery and I tried reinstalling trickdroid but its still getting stuck. Not sure what to do at this point. I don't think I can put a recovery file on this since I can't connect it to my computer.
Hopefully someone can help us.
But the thing is I can't access recovery. I try to flash it again with the all in 1 tool and it won't work. It says it went through, but accessing it doesn't work.
If its recognised by USB when plugged in computer just run an ruu that's my solution all The time lol
Sent from my HTC One S using xda premium
Ok i somehow managed to get TWR on my phone, but still unable to mount the SD. How do I run the RUU? I downloaded it, but the instructions are flawed I think
Connect with USB to.computer go into faatboot USB then run ruu on pc
Sent from my HTC One S using xda premium
Well I thought the RUU was going to work, but it just stops at the HTC and gives me an error saying I can't. What now?
Ok currently, I relocked my bootloader in an attempt to do the RUU, but I get a 155 Unknown Error up doing such, using the TMOUS 1.53 ruu... other places I have seen say something about returning to the stock img etc, but I'm quite stuck. Any advice appreciated
htc one s stuck in bootloop almost unresponsive
hey guys, got a brain teaser for you.
i have a tmobile htc one s, unlocked, rooted using all in one htc tool, been at it for two days now. im stuck on the boot screen showing its unlocked, i used to be able to get into the boot loader screen but now it seems ive dead ended. ill hold any combination of power and vol up/down, the keys flash for 10 sec and the screen flashes once, i let go and it reboots, keeps that htc screen, after 20-30 sec goes black. my pc doings like it detects a device but i cant locate it. ive used adb and the htc all in one unlock tool trying to get any kind of os to launch.
Shortly before this i was able to go into the boot loader, clear and master reset the files and cache, and search for the rom zip, thus never allowing me to flash. on a journey to place this in the phone through various combinations of the all in one, adb push, and everything else i found on youtube, countless forum posts, i seem to be in a deeper hole now.
I ultimately want to end with a cm10 nightly on my tmo htc one s. I have never done this to a phone without a sd card. i come to this community humbly seeking any and all advice. thank you.
People that can't get the roms beyond stock to work, are your phones activated?
Is it possible to use the Pac Man Rom or CM10 on an unactivated phone?
I'm having similar issues to others trying to flash Pac Man and CM10.2. The first boot was fine and I can access everything on the phone fine, including settings. I rebooted and the activation screen (which I skipped as this phone doesn't have service) always pops up but I would like to use it without putting it on a cell network. I can skip the screen fine (until I decide to disable it) but then have issues like the keyboard (physical and touch), systemUI or NAV Bar crashing with a constant message pop up telling me it has crashed. I have returned to stock using RSD and reflashed Pac Man and CM10.2 MANY (15+?) times, doing a clean install 99% of the time but also trying a couple dirty installs to cover my bases. I should also note that I flashed the phone to Cricket but have no plans to activate it anytime soon.
Another thing to note is that I had issues getting the custom roms to boot at all as the initial setup would take hours. One time I though it was a boot loop but I left it on all night and it had booted in the morning. I believe it has something to do with the file check at boot (with my 32GB low speed class SD card) but that seems to be resolved and I can get the custom roms to boot fine (on the first boot) even with my 32GB (witch is fine and has no errors nor is generic, before you ask.) I also have tried 2 4GB cards and a 2GB card, all different brands, with no change in behavior.
I have done everything below multiple times and in different orders.(If needed I can give a direct breakdown step by step but if you could do it with the files below, I have probably tried it)
Wipe the phone (including all storage internal and external SDs included)
Using RDS v6.15
RDS asanti_c_sprint-user-4.1.2-9.8.2Q-122_XT897_FFW-5-6-release-keys-cid9.xml.zip (Works 100% of the time and never has issues. I keep reverting back to this if I actually need to use the phone)
RDS ClockworkMod, TWRP, and Open Recovery without TWRP (Tried different versions when available)
Then used each recovery to install Pac Man or CM10.2 (tried 10.1 once but had the same issues and I didn't see the need to troubleshoot a rom people seemed to not want to develop for. So 10.1 was only tried once but has the same issues)
Installed GApps at this point but I also tried alternate versions of GApps and not installing it at all. All have the same effect and don't seem to be contributing to the problems at all.
A few installed I tried wiping the phone again or installing each zip multiple times. I also verified the zips were good when on the device to make sure there was no corruption at transfer.
I also tried multiple (confirmed working) SD cards and installing from the internal storage.
I have tried installing arrrghhh's Kernel too.
The issue ether seems to be boot loop (if it's doing a file check) or more often it works until I get one of the said crashes after a reboot.(blame Tyler message is getting SO old...) The time I see the errors seems to be accelerated if I mess with the settings a lot but I don't believe it is directly related to the settings.
My next recourse is to try and flash it back to Sprint (maybe check my Cricket settings) and see if that helps, without it being activated.
On a separate note.
If people need help I can help get you back to stock easily. The instructions/guides on here are all but useless if you don't know what you are doing already. I have seen down to "USE RDS" or "DELETE LINE MD5" like people would just know what that means. I understand RDS Lite is a standard tool for flashing phones but it's nigh impossible to find real explanations on what stuff does in context. I understand the basics though, so if anyone has any questions I can walk you through it.
To start with if you are stuck in a loop at the start of a new rom and it loops between the 'Welcome' Screen (Select your Language) and Activation screen just skip the initial setup by tapping the corners on your screen in a clockwise manor when on the 'Welcome' screen to skip the setup there is a video to explain it here
pocketnow(can't post links )com/how-to/android-quick-tip-how-to-bypass-touch-the-android-to-begin-video
Without doing this or activating the phone it seems to loop between those 2 screens forever (might indicate part of the problem with customs roms....)
I hope this is enough info to go off of I can give you a play by play with the actual files if you need. Maybe a video if needed and I'm feeling extra fancy.
Thanks for your time.
Hey buddy,
If you're trying to make a guide, make sure you call it what it is properly - RSD Lite.
Also, maybe clean up your post a bit so it's a proper guide (as you point out, it's needed) and make a separate thread for your question.
To answer your question, the unactivated phone shouldn't be an issue in of itself - you'll just get the nag screen like you were talking about.
I know there is an issue some are having with rebooting the 4.3 ROM's. Have you tried any 4.2.2 versions of anything? Carbon, CM10.1?
I wonder if your "flash" to Cricket is causing issue, I'm not sure. Let me know about 4.2.
Edit - I missed this part on my first read of your PM. Taking hours to boot is NOT normal. Perhaps remove the SD card entirely, flash using the internal SD... I've never heard of that. Anything over say 20 minutes is probably cause for concern.
Thanks for taking time to answer me.
In no way was I trying to make a guide yet but I guess I could. I just hate posting stuff without useful content so I figured throwing that in was better than nothing. I'll clean it up and set up some links later today. It's frustrating to try and make a full guide before I can post links that would be needed for it. You are totally right though! (complain about crappy guides and kind of make one... )
Part of my point there was that I can't post out of Q and A and this wasn't really a question so I made a question out of it and that's how my post ended up.
I have flashed many phones before but like I said I'll try and put it back on Sprint later today (probably will be a few hours) as I backed up the settings the phone came with. I know it was a wall of text and not the easiest to read so you probably missed it but I also said in my first post that I tried the internal SD card many times and the taking hours to boot isn't the standard and doesn't seem to happen at 99% of the time. It seems to be related to the recovery software I use as it happened a lot more when I was testing TWRP and none when I use clockwork.
What Recovery do you recommend? I swear they aren't made equal...
I tested CM10.1 once and it had the exact same issues as CM10.2 and Pac Man so I didn't test it further but if you want me to test it I can. I just didn't want the Rom.
I don't want Carbon either but I'll test that and AOKP next. It's just annoying that the stock rom works perfect but I can't get these to function at all. I almost wish I didn't get Pac Man to work at all. I'm very particular about my settings and NEED these features after I tried them Pac Man is AMAZING.
Thank you for the help and I hope I can get this worked out.
PS I saw that you were frustrated about working on a rom you don't have a device for. I hope you don't let a little thing like that stop you as, for the little time I have used it, it's all I want. Thanks again.
Blasz said:
What Recovery do you recommend? I swear they aren't made equal...
Click to expand...
Click to collapse
Well, OpenRecovery has probably the most work done for this device specifically. I liked TWRP, but it seems lately it has been unstable - you're not the first who has reported issues lately. I don't think CWM has been updated, unfortunately - but perhaps that's a good thing, it's stable that's for sure.
Blasz- I was just about to start a thread when I found yours, and it very accurately describes the issues I've been having. Here's my progress so far.
I got my Photon Q with Sprint and used it for a few months before Sprint started finding creative ways to take my "$79.99" bill and make it more like $140 a month. Naturally, I refused to pay. So I had a Photon Q with no cell service. This is fine, as I only need it to work on WiFi, not 2G/3G and there is no 4G in the area. Anyway.
At the time, I had Ice Cream Sandwich on it, using the (latest?) ICS firmware from Motorola. This worked very well, but I later tried to use a newer firmware, and all the custom ROMs had shown up while I hadn't been looking. All of these seemed to be based on JellyBean. First off, I tried CyanogenMod 10.2. Worked amazing well! I had literally no problems at all. However, while I was experimenting with different software for the phone, and wanted to see if "Arrrgghh"(sp?)'s kernels would give me some decent overclocking capability. Turns out, the kernel I picked wasn't compatible with the JB firmwares (I probably picked an older one by mistake.) Needless to say, it now wouldn't boot. It'd go to the "Unlocked bootloader" screen and stay there all night (literally, I tried that.)
So, I went back into CWM, which is the recovery I have installed. I erased /data, /cache and /system, and also the dalvik cache and battery stats for good measure. I also formatted /pds and /modem, I believe, which was probably dumb of me since I'm not sure what those do. Then I tried re-installing CM 10.2 from CWM. The installation went fine, and it works gorgeously. However, there's two weird issues:
1) WiFi and Bluetooth don't even BEGIN to work! Neither does Cell, as far as I can tell, because where CM used to be unable to make calls or access the internet (of course, I've not been paying my bill), it now shows an empty signal bar or "No Signal" (the little red X) in the notification bar ... When I try to turn on WiFi using the slider in Settings, it moves to "ON" (stays gray) and pauses for a few secs, then goes back to OFF. Same thing for BT. If I open the WiFi menu where you select an AP, it tells me to turn on WiFi. I do, using the slider up top, and the same thing happens. WiFi and BT simply won't turn on. Tried fiddling with every setting I can find.
Before this misadventure with the kernel/reinstall, WiFi worked great. I connected to a local AP and was surfing the net and downloading apps.
2) The system takes a VERY long time to boot up. It sits at the "Unlocked Bootloader" screen for up to a whole minute. Then it goes to the Cyanogen screen for about 30 seconds. Then it gets to the homescreen. It's fine so long as you let it boot up, but this doesn't seem normal.
Next I tried other ROMs thinking that might help. I installed AOKP, PacMan, CM1.0, Carbon, SlimBean, and I think a few others without results-- they all work but WiFi and BlueTooth are dead. PacMan is the only exception-- it boots up and then endlessly gives me "Blame Tyler" errors until I force the machine to shut off.
I also tried an older ROM, since these are all JellyBean ROMs and I wanted to get back to ICS (I'm not that fond of JB's interface) anyway. I was unable to find any ZIPs I could install through CWM of the stock firmware. I found some IMGs that it looks like I could install via Fastboot, but I don't currently have a PC with admin priveleges (it's not mine) so I can't install the drivers to use Fastboot or any part of the SDK. (I can, however, put files on my SD card, that doesn't require privleges.) The closest ROM I found to stock was "TwistedAsanti" beta-1 or whatever it's called. That installs fine, but again, it takes about 2 straight minutes to boot and it's useless after that:
It gets stuck at "Starting Services..." and will sit there forever, even left there all night. Behind this, a dialog pops up saying no cell networks were found and asking if I want to switch to GSM. (i've been trying GSM and CDMA ROMs all this time, I don't need cell access so I doubt it matters which I use. I'm in the USA.) You can pull down the notification bar and get into the Settings, and even launch a couple programs, but I can't find ANY way to get to a homescreen. Task manager shows Circles is running, which is a widget on the homescreen, so where the heck is that screen? .. I try, again, to turn on WiFi or BT without success. The friggin thing just won't turn on.
Did I eff it up by erasing the "PDS" or "modem" partition? Am I missing something obvious or is my phone just possessed?
In a few days I should have access to a computer where I can hopefully use Fastboot and see about installing a stock firmware (wish me luck). Until then, does anyone have a ZIP file I can flash from CWM to get back to an ICS firmware? I managed to find a copy of the stock firmware, in the form of a dump done from TWRP (in .win files). But as far as I know the only way to install TWRP is using Fastboot, and I've explained why I can't do that. I don't know a way to install TWRP from CWM. Maybe I can do it from CM10.2, if I can put APKs or something on my SD card. I can't get it on the network, so I have to copy all the files manually. Needless to say, it's a pain.
After my frenzy of ROM installing, I got frustrated and decided to see if TwistedAsanti would do SOMETHING if I let it sit at "Starting Services" overnight. To my mistake, I left it under my pillow and the system was quite toasty, and the battery had run dead. Plugging it back into the charger, it made a few worrying clicking noises from the speaker, then the green LED came on. This LED seems to mean "I'm charging, but the battery is too dead to turn on for a while." After it sits there a while, the green LED turns off and it just goes black. Or it goes to BOOTLOADER UNLOCKED and bootloops, or goes to black untilyou fiddle with the power button some more. I can once in a blue moon get to CWM. Sometimes it gets to the homescreen. It will charge up to about 4-7% and no further (battery got damaged by the heat?) It doesn't reliably work when plugged in, it likes to shut off at random anyway.
So now I'm stuck with a phone I can't seem to charge, or turn on reliably, and if I *do* get it to boot up, there's no way to connect it to a network.
Needless to say I'm pretty darn frustrated..
Thanks for any advice.
Epicenter714 said:
So now I'm stuck with a phone I can't seem to charge, or turn on reliably, and if I *do* get it to boot up, there's no way to connect it to a network.
Needless to say I'm pretty darn frustrated..
Thanks for any advice.
Click to expand...
Click to collapse
Did you try to use RSD Lite and flash the device back to stock?
arrrghhh said:
Did you try to use RSD Lite and flash the device back to stock?
Click to expand...
Click to collapse
Currently, I have no PC to use that has Admin priveleges, so I can't install the USB drivers or RSDLite. I also can't use fastboot to install TWRP to use the TWRP .win backups I found.
I did get a roommate to let me use his laptop for 10 minutes to try RSD Lite, but I had this result: Loaded the ".xml.zip" file for the 4.0.4 and 4.1.2 firmwares (after removing the 'getvar' line that causes problems) and it says the phone reported "FAIL". No further details. MiniRSD gives no info from the phone other than the model (it all stays blank), is that supposed to happen? I have the phone in "AP Fastboot" mode so I don't see the problem.
The guy who let me use his PC momentarily is computer-illiterate and thinks anything will break it, so he only let me use it momentarily, and won't let me touch it because I accidentally left an icon on his desktop. I'll have to ask someone else, I think I may know somone..
If I do, how do I get around this error in RSD Lite? Will keep doing research on my own .. thanks!
Epicenter714 said:
Currently, I have no PC to use that has Admin priveleges, so I can't install the USB drivers or RSDLite. I also can't use fastboot to install TWRP to use the TWRP .win backups I found.
I did get a roommate to let me use his laptop for 10 minutes to try RSD Lite, but I had this result: Loaded the ".xml.zip" file for the 4.0.4 and 4.1.2 firmwares (after removing the 'getvar' line that causes problems) and it says the phone reported "FAIL". No further details. MiniRSD gives no info from the phone other than the model (it all stays blank), is that supposed to happen? I have the phone in "AP Fastboot" mode so I don't see the problem.
The guy who let me use his PC momentarily is computer-illiterate and thinks anything will break it, so he only let me use it momentarily, and won't let me touch it because I accidentally left an icon on his desktop. I'll have to ask someone else, I think I may know somone..
If I do, how do I get around this error in RSD Lite? Will keep doing research on my own .. thanks!
Click to expand...
Click to collapse
Well remember - if you are on JB and you are downgrading to ICS, there are additional lines to remove.
Other than that, not sure why it would fail. Make sure 'fastboot devices' works in the command line before doing RSD perhaps.
arrrghhh said:
Well remember - if you are on JB and you are downgrading to ICS, there are additional lines to remove.
Other than that, not sure why it would fail. Make sure 'fastboot devices' works in the command line before doing RSD perhaps.
Click to expand...
Click to collapse
I'm trying to wipe the device clean and install ICS. Are there any other lines I need to remove? ..
As for Fastboot.. I did 'Fastboot Devices' and got no devices listed. How come it shows up in MiniRSD? .. I have the drivers installed, Windows says it installed an ADB device successfully. What are some reasons that might not work? Is there any sort of guide for this? Thank you
---------- Post added at 05:51 PM ---------- Previous post was at 05:29 PM ----------
Oh, as far as the weird booting problem, it seems the battery is fine and the charger died coincidentally at the same time as the overheating did. So my only problem is software now.. thanks.
Epicenter714 said:
I'm trying to wipe the device clean and install ICS. Are there any other lines I need to remove? ..
As for Fastboot.. I did 'Fastboot Devices' and got no devices listed. How come it shows up in MiniRSD? .. I have the drivers installed, Windows says it installed an ADB device successfully. What are some reasons that might not work? Is there any sort of guide for this? Thank you
---------- Post added at 05:51 PM ---------- Previous post was at 05:29 PM ----------
Oh, as far as the weird booting problem, it seems the battery is fine and the charger died coincidentally at the same time as the overheating did. So my only problem is software now.. thanks.
Click to expand...
Click to collapse
I have no clue what MiniRSD is - you mean RSD Lite?
If it doesn't show up in fastboot devices, sort that out before trying to use RSD.
As I stated previously, if you were on JB and going down to ICS you have additional lines which are needed to remove.
Yes, RSD Lite. I don't know where I got MiniRSD from.
I got it to show up in fastboot devices, but adb devices doesn't show it. Weird. Is that OK?
I was able to flash TWRP to the phone with Fastboot. RSD Lite was unable to find the phone. However, I opened the XML file and was able to figure out the flash commands to enter from a command prompt, so I did that:
I got these results... all of the files flashed successfully to stock, except for two. I forget the first, haven't got it in front of me, but here's the big one: SYSTEM! (Important, no?) Here's the error from fastboot:
>> fastboot flash system system.img.ext4
fastboot said:
target reports max download size 31457280 bytes
Invalid sparse file format at header magi
Click to expand...
Click to collapse
(then, Fastboot crashes.)
Does anyone know how to fix that? Also, the system image is way bigger than 31.4 MB. What is it talking about?
Thanks!
Epicenter714 said:
Yes, RSD Lite. I don't know where I got MiniRSD from.
I got it to show up in fastboot devices, but adb devices doesn't show it. Weird. Is that OK?
I was able to flash TWRP to the phone with Fastboot. RSD Lite was unable to find the phone. However, I opened the XML file and was able to figure out the flash commands to enter from a command prompt, so I did that:
I got these results... all of the files flashed successfully to stock, except for two. I forget the first, haven't got it in front of me, but here's the big one: SYSTEM! (Important, no?) Here's the error from fastboot:
>> fastboot flash system system.img.ext4
(then, Fastboot crashes.)
Does anyone know how to fix that? Also, the system image is way bigger than 31.4 MB. What is it talking about?
Thanks!
Click to expand...
Click to collapse
I would NOT recommend entering those fastboot commands in the XML file manually unless you KNOW what you are doing.
Sort out why RSD isn't working. adb and fastboot are two different things. If fastboot devices shows the device, RSD Lite should work fine. Try again.
Hey folks...I'm running into a problem I was hoping someone might be able to help with.
Earlier today I pulled my phone out of my pocket at work and saw that it was off...I thought that the battery must have died sooner than I thought. I started charging it in the car on the way home and it wouldn't boot up like normal. It would get to the google or "dots" screen and then reboot. I again thought that the battery might just be really low. After getting home and charging the phone all the way I still can't get it to boot up. As of now, one of 3 things will happen...
1-The phone will turn on, get to the google screen and bootloop (usually when plugged in).
2-The phone will turn on, get to the google screen and freeze.
3-Get to the "dots" screen and either swirl forever or eventually reboot and do one of the above again.
I've read some threads where people suggest this is a faulty power button, that doesn't seem to be the case for me though because I can get into fastboot and it won't select anything or turn off without me doing it.
I've used WugFresh NRT and wiped/reflashed android. I'm running out of ideas. Do you have any others?
I was running the stock 5.0.1, unlocked, not currently rooted.
Thanks!
kyle313 said:
Hey folks...I'm running into a problem I was hoping someone might be able to help with.
Earlier today I pulled my phone out of my pocket at work and saw that it was off...I thought that the battery must have died sooner than I thought. I started charging it in the car on the way home and it wouldn't boot up like normal. It would get to the google or "dots" screen and then reboot. I again thought that the battery might just be really low. After getting home and charging the phone all the way I still can't get it to boot up. As of now, one of 3 things will happen...
1-The phone will turn on, get to the google screen and bootloop (usually when plugged in).
2-The phone will turn on, get to the google screen and freeze.
3-Get to the "dots" screen and either swirl forever or eventually reboot and do one of the above again.
I've read some threads where people suggest this is a faulty power button, that doesn't seem to be the case for me though because I can get into fastboot and it won't select anything or turn off without me doing it.
I've used WugFresh NRT and wiped/reflashed android. I'm running out of ideas. Do you have any others?
I was running the stock 5.0.1, unlocked, not currently rooted.
Thanks!
Click to expand...
Click to collapse
Did you try flashing factory images?
ryukiri said:
Did you try flashing factory images?
Click to expand...
Click to collapse
Yeah, that was what I flashed :/
If you can get into fastboot you "should" be able to flash stock images... Obviously this will revert any root and you will need to flash TWRP/CWM recovery after.
I assume you have a Windows PC with fastboot/adb setup and all drivers etc..
- Download latest "stock" hammerhead images (I cannot post links due to XDA rules... so: "developers.google.com/android/nexus/images#hammerhead"
- Extract the .tgz archive contents on your PC into a folder
- Boot the N5 into fastboot and plug USB cable from phone into your PC
- Go to the folder with the extracted files and run the "flash-all.bat" script on Windows
**Hopefully at this point your device will start to respond.. I.e, on fastboot screen, at the bottom you will see "writing" or something, as the script runs on the command window on your PC.**
If this works, you should be able to reboot once complete and then wait to see if you can get back into your phone.. then you can fastboot again and flash custom recovery, and then whatever rom.
If however you have a hardware issue (i.e, even after the above process it fails) then I am not sure what you could do... I guess ensure it has a complete charge. If you can get into fastboot and the buttons are responsive then it should not be a faulty power button.
Hope this helps :good:
Have you tried a simple factory reset? Reason I ask is it was working fine so sounds like something needs "flushing out" clear cache etc.
kyle313 said:
Hey folks...I'm running into a problem I was hoping someone might be able to help with.
Earlier today I pulled my phone out of my pocket at work and saw that it was off...I thought that the battery must have died sooner than I thought. I started charging it in the car on the way home and it wouldn't boot up like normal. It would get to the google or "dots" screen and then reboot. I again thought that the battery might just be really low. After getting home and charging the phone all the way I still can't get it to boot up. As of now, one of 3 things will happen...
1-The phone will turn on, get to the google screen and bootloop (usually when plugged in).
2-The phone will turn on, get to the google screen and freeze.
3-Get to the "dots" screen and either swirl forever or eventually reboot and do one of the above again.
I've read some threads where people suggest this is a faulty power button, that doesn't seem to be the case for me though because I can get into fastboot and it won't select anything or turn off without me doing it.
I've used WugFresh NRT and wiped/reflashed android. I'm running out of ideas. Do you have any others?
I was running the stock 5.0.1, unlocked, not currently rooted.
Thanks!
Click to expand...
Click to collapse
Did you choose the right model and firmware before you flash in WugFresh NRT?
The above could be right, however when I've used it, it's pointed out if I made that mistake. Having used his software dozens of times I've found it will bring any Nexus 5 back to life.
howard bamber said:
The above could be right, however when I've used it, it's pointed out if I made that mistake. Having used his software dozens of times I've found it will bring any Nexus 5 back to life.
Click to expand...
Click to collapse
Hello! I am apologize for that I didn't read the OP carefully. This happened to me once in that particulary way, but it was immediately after flashing. OP says that it happened suddenly, without reason. So now I am the one, who doesn't read, right? Sorry for that.
Regards, Zagor
Thanks for the responses, but I'm still having trouble.
I have been able to successfully write the newest stock android 3 times (1 without full wipe, 2 with) and the phone still can't boot up and goes through one of the three issues above.
I've also been able to get to the system recovery from the bootloader and I've tried wiping the cache and doing a factory reset from there and the problem remains.
I'd contact google, but I bought it at launch so I don't think they'll do anything for me since it's been 1+ years.
kyle313 said:
Thanks for the responses, but I'm still having trouble.
I have been able to successfully write the newest stock android 3 times (1 without full wipe, 2 with) and the phone still can't boot up and goes through one of the three issues above.
I've also been able to get to the system recovery from the bootloader and I've tried wiping the cache and doing a factory reset from there and the problem remains.
I'd contact google, but I bought it at launch so I don't think they'll do anything for me since it's been 1+ years.
Click to expand...
Click to collapse
Sounds like you have a bad nand sector. From fastboot try:
Code:
fastboot oem lock
Then reboot into fastboot and check if it's locked or not. If the device isn't locked your emmc is corrupt and there is nothing you can do. If that is the case call Google and they will most likely help you out with a RMA.
theesotericone said:
Sounds like you have a bad nand sector. From fastboot try:
Code:
fastboot oem lock
Then reboot into fastboot and check if it's locked or not. If the device isn't locked your emmc is corrupt and there is nothing you can do. If that is the case call Google and they will most likely help you out with a RMA.
Click to expand...
Click to collapse
I was actually able to relock the phone.
Luckily I called google and they're going to send me a replacement.
If anyone else has any other ideas, I'll still take them...I'd rather not be without a phone for the next week!
You won't be without a phone - they are sending a refurbish unit to you , putting a block on your credit card and waiting for you phone to arive at them. Once that happens they will release the funds.