Database Info

Stuck in bootloader & error 302

I've been running a ROM I built from the consolidated kitchen this weekend without any problems. Today I updated the radio to 2.69.11 from the cingular 2.25.11. After the flash the phone froze on the windows mobile screen. After some time I tried to reset the phone and it froze again, a few more tries and it finally boots up. I didn't pull the memory card when I flashed and thought that might have been the problem so I flashed again even though the phone was showing 2.69.11. I don't remember everything after that but it wouldn't boot up and I have tried flashing the original Cingluar ROM & T-mobil 2.26 without any luck.
The phone is stuck in bootloader now and is getting a error code 302 I think it's because the phone doesn't stay on when the USB cable is attached. It gets to about 15% and the phone resets and the error 302 pops up. When connected and not trying to update the phone turns on and off in the bootloader screen. I have pulled the battery, rebooted the laptop, tried using mtty,and pulled the sim. I thought the original problem might have been because I flashed at 52% battery. I put a older battery in after that appeared to have a good charge. Right now I put the phone on charge with the newer battery to see if this helps. I am not sure if it is charging because the orange light is not on, I can't get the phone to stay turned off when plugged into the charger and the bootloader screen is on.
And yes I have been searching for hours for a solution to this problem.
Also looking for a post I read about doing a master reset, I have tried holding the 2 soft keys when turning on, didn't help.
I think this says it all I have tried everything, does anyone anything else to try?
Thanks

UPDATE: went out for a few beers and some food. Not sure it the battery charged (bootloader screen on the whole time it was plugged into the charger)
Tried flashing again with cingular ROM, got about 20% and phone shut off and turned on again in bootloader. Flash gave 302 error again. Tried again and phone reset (on and off) every 5 seconds when connected to laptop with USB.
I'm hopping someone out there has a answer for this problem.

Back from the dead HALLAULA!!!!
This morning I spent more hours searching still didn't out find anything.
I tried mtty again and noticed that I never got to the screen that shows USB>
to enter the command "set 14 0"
I came up with a thought and this is what I did. Created a new ROM, OS only. Thinking it will load faster than any other ROM. It reached 100% in 3 minuets the whole I'm coaching come on baby don't restart and than going (don't know how to explain the feeling) waiting the next 2 minuets to get to finished. But it got there booted fine. I don't know why it stayed on this time and didn't restart, maybe having the battery out all night had something to do with it. After I flashed the Cingular ROM than the original I created and lastly Radio 2.69.11
I hope this helps someone in the future,

i need your help
hi man I had a prophet s200 and give me the same error 302 but, with the diference in my case got 98% adn then stuck in boot screem, please help me if you can...and sorry for my english

Guys,
It may help checking out this thread!
http://forum.xda-developers.com/showthread.php?t=294107

Can you help me out?
How did you create a new ROM - OS only? I'm having the same problem..can you walk me through this?
Thanks

How did you create another ROM (Operating System only)? I'm having the same problem and I have tried for the past 2 weeks - but no luck. Can you walk me through it?
Thanks

I used the consolidated kitchen (sticky at the top of this forum)
Uncheck everything on Build OS.
My problems started from a version of battery status that caused the original problem and not having enough of a charge on my battery.
Make sure you are CID unlocked (if you have a G3) and your battery is charged.

Umm, you can't uncheck everything in build OS or you will have problems, especially if you don't check a tuchflo or non touch flo dll or choose a commanager and probably a few others things. I don't have build OS up in front of me to check. The whole point to this msg is that you can check everything in build OS (besides the ones that say choose only 1) and it will build an OS only rom for you. That's the whole point behind build OS.

You are correct, I was kind of going from memory since I had built the striped down ROM awhile ago.

Is my S200 beyond repair?

After I tried to upgrade the rom to WM6, my JAMin got stuck at bootloader. After that, I tried to flash WM5 roms without success and suddenly (after a reset) the screen became white with some horizontal and vertical lines constantly moving. I discovered that it was only the screen that was garbled as it still connected to PC, so I installed (without seeing anything on my JAMin) the NVID ROM trying to restore it. It installed sucessfully, but the screen remained garbled with the white background and random lines. I know it was sucessfully installed because I heard the typical "welcome" sound before configuration.
Do you know any way to restore the screen? Or must I send it to I-Mate to repair?

You can try and reattach the screen cable to the rest of the device, but this will boid any warranty you have, and may damage your device further. If the device is under warranty, I would suggest flashing the ROM the device came with (unfortunately the FTP server is down at the moment, so it might take some fishing around for) and sending the device back to get repaired properly.

mpmf said:
After I tried to upgrade the rom to WM6, my JAMin got stuck at bootloader. After that, I tried to flash WM5 roms without success and suddenly (after a reset) the screen became white with some horizontal and vertical lines constantly moving. I discovered that it was only the screen that was garbled as it still connected to PC, so I installed (without seeing anything on my JAMin) the NVID ROM trying to restore it. It installed sucessfully, but the screen remained garbled with the white background and random lines. I know it was sucessfully installed because I heard the typical "welcome" sound before configuration.
Do you know any way to restore the screen? Or must I send it to I-Mate to repair?
Click to expand...
Click to collapse
Hi frd,
I have exactly the same problem!
Nothing , only the f*** white screen!
I can browse the device via active sync, can rcv calls but the white screen.
I have checked the ribbon connector of the LCD and make reflashing some ROMs but nothing.
I still wondering is it hardware or software problem!
Please let me know if you have progress!
Thanks
G.

Try to replace LCD module, I think thats right way.

It will be a hard ware problem. Probably the ribbon cable as the screen is showing something so it must be working at least a bit.

Hello,
i have the same Problem with my QTEK S200.
First i changed the Rom and it worked perfectly for two days.
Then i had to change my Sim card and after that the problem came again.
I tryed a lot of times to reflash the rom but the problem persist.
How can it be that it worked again for some days ?!
is it the touchscreen of the lcd unit i have to replace ?
is it possible to do it by my self ?
thanks for your help !

Hi everyone.
I had a similar problem an hour ago (Qtek S200 G3):
I Upgraded to a 6.1 rom and then to another, after that my device was stuck in bootloader(3 colour screen). Any 6.1 rom that I tried would install, but after installation device always boot in to the 3 colour screen.
I tried this original shipped rom http://files.mail.ru/HZUAH1 (it's WorldWidwEnglish) (to download just click the link "скачать" or the file name RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
) and it installed!!! It TAKES A WHILE TO INSTALL!!! But it worked!!!
May want to try it.
Hope this helps.

hello,
picture on screen was immediatly clean again ( bootload image ).
it was impossible to change the rom because i have a G4 model.
i flashed the rom with another french rom for G4 and it worked perfekt.
now i tried to remove the battery again for 3 seconds and now i have the same problem again. really strange ....
i tryed the same procedure again but no success.

I reinstalled differents rom's again starting always installation from bootloader.
After about 10 new installations i've clean picture again.
now i'll not put off, restart, or take of battery till one of you know what's the problem.
Thank you for your help !!

are you guys sure its not an intermitant hardware problem, it sounds like it to me. if yu were able to get a clean picture for a short time and now its white again, it cannot be the rom? As for replacing it, nothing is impossible and there is always ebay and google

QTEK S200 G4 CID unlock
How can I CID unlock a device that need´s that to upgrade the Rom?
Is there already any program that , Lockwiz dont do the job, can performe the unlock?
Thank you.

For G4 CID unlocking, you need to user Hard/Soft SPL.

same problem
my imate jamin got the same problem. it happens only and only when I remove the battery and when I leave it to charge for 1-2 days the LCD works again and show clear pic. any suggestion? activesync and &... are all ok!

Well, i upgraded to windows Mobile 6, but haven't removed the batterie anymore.
But i'm able to put it off now, what was impossible before.

Qtek S200 Bricked ??!!

It may be that my q-tek is bricked. To cut a long story short I am rebooting and it is getting stuck on the QTEK page displaying:
IPL 2.20.0001
SPL 2.20.0001
GSM 02.47.21
It also had OS2.20.7.34 but this is not showing.
Problem is - this is a swisscom fone and therefore I cannot access the original QTEK site as it fails to recongise my IMEI.
I have also tried in my ignorance to reflash it but now its stuck.
Is there anyway I can have access to the original English software so that I can try to reflash and re-install from scratch?
I also wanted to add that even a hard reset is not getting it to start up.
And another thing - sometimes the screen just freezes and breaks up in line and colours. What is that? Is my fone dead or dying?
Any help will be appreciated.
Delgada

The three colour screen is bootloader. If you can get that, your device is recoverable.
edit: http://wiki.xda-developers.com/index.php?pagename=Prophet_recovery
This does work, I wrote it from past experience....

Hi,
thanks for your help. Did all your link said.
IT LIVES AGAIN!!!!! THANKS
One question though - if my fone still goes off and the screen feezes and fades out or breaks into lines - what sort of problem would that be?
Cheer!
Delgada

Depends... It could be the ROM, it could be the ribbon cable connecting the screen to the motherboard, it could be an IC (but I doubt that as you say it works)...

Hi.
I realised that last time i opened my Qtek something must have not been in place as I was pressing the case and the pda was freezing. I opened it up for the umpteenth time and made sure all contacts were ok and closed it carefully. It now works fine. Last hiccup - getting it to read my home wifi when it reads everyone elses already.
Thanks
Delgada

HELP! Imate SPL camera not working!

hi! i have an imate spl which was working ok. suddenly the camera stopped working, the camera application just freezes and doesnt switch on at all. the windows mobile busy cursor just keeps running. also, the task doesnt show in any of the running applications.any help available??

Hard Reset or update software if it fails stil could be hardware failure

Im screwed!
tried ahard reset. attempted a rom upgrade. went fine....but had a power cut in between so my phone now shows a white screen which says update again, connect usb and wait. any way to get around that? i have my limited warranty intact. will this cover it? it was an official rom i tried to upgrade to, by the way. can u help?

Bootloader issue

Phone is an E650 from orange
Complete newbie, i have been trawling xda-dev for 2 days and trying various solutions but im stuck, the phone is stuck at the red green blue screen, i have tried the hard reset and even managed to connect using the mtty software, the phone wont connect to active sync nor will it do anything else, i have flashed the phone several times and still the same dam screen its really annoying now, mem card removed still same issue, any help greatful

Did you search the forum already? Are you aware of the specialties attached to upgrading an Orange device? Did you follow the ROM (which?) specific descriptions?
To get support you should take the time to describe in detail where you started, what you did and where it failed. The end-result (RGB screen) can be reached by many paths.
The only way out for you is to re-load an Orange E650 Build and restart.