Related
I followed Dr. Puttingham's thread and Yippie's thread to a tee in addition to reading threads in this forum for a good number of hours each day for two weeks. Yesterday, I became brave enough to downgrade my 2.26 Ipl / 2.26 spl; GSM 2.25.11; OS 2.26.10.2 MDA with a goal to upgrade to a custom WM6 rom with touchflo.
* Started with flashing the button rom then cid unlock with lockwiz2b which looked successful no errors but got a 1.xx IPL / 2.26 SPL since I got a 2.26 SPL then
* flashed the wizard love rom then then cid unlock with lockwiz2b which looked successful also but got the same results - a1.xx IPL / 2.26 SPL again then
* flashed the 2.26 T-mobile rom from the Tmobile website then
* flashed NBD 8.3 only to go back to Tmobile's 2.26 rom - DISAPPOINTED after two hours...............
Any assistance would be appreciated without bricking my MDA. Also, I read the thread on how to install a 2.x rom in a cid locked G3, this method appears a little bid complicated and if I need to move forward with this method, would this method work for any WM6 rom with touchflo and if somebody could simplify the method in layman's terms for newbie's like me could understand, please advice.
Let me know if I missed anything in the process.
Thanks, Technobuff
After u do cid unluck and sim unluck and its reboots do a downgrade again to the button rom and ur ipl and spl will change.(u do not have to re-due the onlucking procedure again)
I tried again performing Dr. Puttingham's CID unlocking process in terms of flashing the button rom then the CID unlock process using Lokowiz2b but while I am at the DOS screen trying to CID unlock my MDA it the DOS screen showed unlocking phone........DO NOT DISCONNECT UNTIL THE PHONE REBBOTS.
This process went on for 5 then 10 then past 30 minutes until I gave up. To be on the safe side I turned off the LAPTOP by taking the battery then pulled the USB cable from the PC to the MDA.
What is the typical timeframe for the unit to CID unlock? Why is is it hanging? Am I missing or skipping the process? How can I complete the process?
Any help would ber greatly appreciated by newbies who read threads.
Technobuff
The problem is that you need to have an IPL/SPL of 1.xx before you try to unlock your phone. CID unlocking will not change your SPL which means that you had an IPL of 1.xx and an SPL of 2.26 before you even tried to unlock. You need to reflash the button ROM over and over until your IPL and SPL both show 1.xx and then run lokiwiz.
dont get your point, i have been using shelltool for ages without any problems and quite a lot custom roms. my SLP/IPL is 3.08.
regards
irm
unlock problem
if your device doesn't reboot almost at once after the unlock, it probably didn't work. That is what happened to me. Did you get four lines of File cannot be opened or a similar message? I got that from following the 17 steps carefully. What was wrong for me was unzipping to the root directory of C:/. When I redid it to the desktop and executed from there, no problemo.
Your symptoms sound exactly like mine. I posted a longer thread, somewhere....
LH
Ok i did a little booboo and yesterday was using equinoxe's softspl tool by mistake (didn't notice i had a g3), this causes you to actually end up with the exact same os you had before you flashed.
The best advice I can give: Open the Dr's guide and follow every step closely. (also just found this guide. Its a bit simpler http://forum.xda-developers.com/showthread.php?t=305225)
Once you CID unlock you should be able to use the RUUs to flash.
Make sure everytime you do any of the steps that dr. putt gives to be comepletely synced to activesync.
Also dont forget to load enablerapi.cab on your wizard.
Also you must use the unlock function before the cid unlock function in lokiwiz.
OH also the unlock will work after your ipl drops to 1.xx After you do the unlocks reflash button to drop the spl to 1.xx Then just flash up to a higher IPL/SPL as the Dr states.
If it seems unorganized im sorry =P
4irm said:
dont get your point, i have been using shelltool for ages without any problems and quite a lot custom roms. my SLP/IPL is 3.08.
regards
irm
Click to expand...
Click to collapse
Umm I believe the IPL/SPL of 3.08 means your phone is unlocked... so you really shouldnt need to use shell tool. Some correct me if I'm wrong
slod said:
Umm I believe the IPL/SPL of 3.08 means your phone is unlocked... so you really shouldnt need to use shell tool. Some correct me if I'm wrong
Click to expand...
Click to collapse
Just cause you have 3.08 does not mean you are unlocked..you could have upgraded a 2.xx ipl/spl without having downgraded and unlocked first.
thanks. helps me to learn stuff.
CID???
how wil i know if my fone mda vario is CID unlocked?
it is now installed with t-mobile 2.26 ROM
thanks.
rizortiz
famewolf said:
Just cause you have 3.08 does not mean you are unlocked..you could have upgraded a 2.xx ipl/spl without having downgraded and unlocked first.
Click to expand...
Click to collapse
right, i installed the latest german t-mobile rom and my device is still locked. the point i made is why the hell does somebody want to downgrade? It doesnt matter if u use the shelltool.
regards
irm
4irm said:
right, i installed the latest german t-mobile rom and my device is still locked. the point i made is why the hell does somebody want to downgrade? It doesnt matter if u use the shelltool.
regards
irm
Click to expand...
Click to collapse
Perhaps they want it actually cid unlocked for resale value...or perhaps they prefer the RUU method of installs vs having to use shelltool.
hi,
I have just use the great work from jockyw2001 on the USPL 1.16 to make:
USPL 1.34 from RUU_Vox_HTC_FRA_1.34.406.1_4.1.13.54_03.10.90_Ship
USPL 1.35 from RUU_Vox_ORANGE_UK_1.35.61.1_4.1.13.60_03.18.90_Ship
Currently i use the RUU_Vox_HTC_WWE_1.34.405.1 and i have follow this thread
to upgrade from SPV650
use CID-Bypass 1.34 and RUU 1.34 to USPL 1.34
upgrade RUU IPL/USPL 1.35 with Vox-IPL-USPL-1.35.patched
All files have work for me, i hope this work for you to
Credits: pof and jockyw2001
This is still a soft SPL? What benefits does this serve over the previous uSPL by jocky?
lol~~~~
tested, both of USPL and hardSPL worked fine.
The hardSPL version is 1.35.0000Cy
Thank you for your great job.
h4waii said:
This is still a soft SPL? What benefits does this serve over the previous uSPL by jocky?
Click to expand...
Click to collapse
I dont know the change between the SPL 1.16 and 1.34/1.35. The patch
method was strictly the same. This is just for people like me who want
everytime the last release
I see.
Well thanks for your work in patching the new SPL. Hopefully somebody can merge or sticky this thread.
which file should i use for hard SPL? will it work forever means i can update any VOX unofficial ROM without running any SPL later?
It works as long as you don't flash an official ROM. It doesn't really matter which one you use. 1.16 is working perfect on my device, so should these!
frauhottelmann said:
It works as long as you don't flash an official ROM. It doesn't really matter which one you use. 1.16 is working perfect on my device, so should these!
Click to expand...
Click to collapse
1.16 is USPL means software SPL, i also use that to bypass CID and it needs to run everytime whenever you are flashing any ROM.
But my concern is if there is some Hard SPL and i run it on my VOX once, would i need to run USPL/HSPL again whenever i need to flash any ROM or will it work forever so that i can simply flash any ROM without using any SPL further.
If you FLASH uSPL instead of simply patching it through RAM, you will have an SPL that acts HARD until you flash an official ROM as it will overwrite the SPL since it is not a true HardSPL.
Take the same steps to patch uSPL and then instead of flashing your ROM, run FLASH.exe from within the uSPL directory, flash USPL and then flash your unofficial ROM. Patched uSPL will remain on the device and thus it will act as a HardSPL to any unofficial ROM and you will not need to patch SPL every time you flash an unofficial ROM.
Will this USPL allow me to flash an unofficial ROM on my Vox that has got the latest WM6.0 Orange UK ROM on?
Roland
Please help..
Hello, i have an Orange France SPV e650, every time i run sda application unlock thing it says "phone not unlockable" then it says succesfully unlocke, now it wasnt succesfully unlocked cos the flash does not work, stops at 3 percent.... Please help me I really look forward to ROM upgrade.
Thank you,
Sammy
BIG THANKS TO ChiemY
I can't believe how long it took me to solve this riddle lol. Was trying use Vox USPL- CID BYPASS for 1.16 and just took a lucky guess at using the number that seemed to be shown on the bootloader so often being 1.34 . It's my first time playing with WM HTC devices and it seems it will be smooth sailing from now on .
I flash HTC P3400 with Vox USPL and when phone restart that goes in blank screen, now it does not flsh anything, please help
I flash HTC P3400 with Vox USPL
I flash HTC P3400 with Vox USPL and when phone restart that goes in blank screen, now it does not flsh anything, please help
You have successfully bricked your device - may it rest in peace. The SPL is the part of SW that opens the door to other SW loading. If that does no more work you are lost.
Hey guys! been lurking around the forums for eons, but haven't 'dove in' till just recently. Have a couple of questions.
Some months ago I did the free upgrade to WinMO 6.1.
I got Tilt SID unlocked by calling up AT&T and telling them I was going to Europe. My T-mobile SIM card is working just fine.
After a few hours of cussing, I managed to beat HardSPL 3.56 into my phone, because it already had SPL 3.56 on it.
Now I'm stuck trying to CID unlock and I can't seem to find a utility to work with it. The 'chain' of threads I followed dead ended saying downgrade to get it work, but I don't want to do that. I had a hard enough time getting HardSPL 3.56 to install. Then I ran across Jockyw's CID unlocker http://forum.xda-developers.com/showthread.php?p=1837147 and found myself saying ooo and ahh! But, it won't work with ANY 3.xx HardSPL.
Is there a CID unlocker compatible with 3.56??
I'd love to have AT command mode stuff and etc. from jockyw's, but at this point I think I'll take whatever I can get without needing to downgrade.
I can't seem to find it now, but didn't there used to be a list of pre-cooked ROMs here somewhere?
I think what I'm aiming at is a fully patched / hacked 6.1 HTC ROM with everything fixed and no bugs. Preferably minus any bloatware. If it has recommended utilities pre-installed great, if not, no big loss. Did they ever finish hacking a video driver together? I lost track of that thread, and can't seem to find any current info.
I've been waiting for a working Linux distro for a HTC device for years, but I'm going to throw in the towel and make the best of what I can get on windows. I've spent over $3000 on these HTC devices over the years, but don't rely on them because of all the bugs. Once I get my Tilt patched up, I'm jumping ship and trading in my old ones for a G1.
Thanks for any help!
p.s. I DO have to CID unlock before I can install any other ROMs.. right??
p.p.s. Here's all the details if it's any help:
rom version 3.57.502.2 WWE
rom date 7/17/08
radio version: 1.65.21.18
protocol version: 25.88.40.05H
tri-color screen
KAIS1*0
SPL-3.56.0000
CPLD-8
.
.
Serial
image version 3.57.502.2
R 1.65.21.18
G 25.88.40.05H
D 3.57.00.00
Note: This is BEFORE I updated to HardSPL 3.56
Thanks again!
If you have any of the HARD SPL installed(3.56 from your words).
You can flash any ROM you want.
No need to CID unlock separately.
With Hard SPL, your Device is CID unlocked already.
Your pda doesn't not have hard spl installed on it
Crogon said:
Hey guys! been lurking around the forums for eons, but haven't 'dove in' till just recently. Have a couple of questions.
Some months ago I did the free upgrade to WinMO 6.1.
I got Tilt SID unlocked by calling up AT&T and telling them I was going to Europe. My T-mobile SIM card is working just fine.
After a few hours of cussing, I managed to beat HardSPL 3.56 into my phone, because it already had SPL 3.56 on it.
Now I'm stuck trying to CID unlock and I can't seem to find a utility to work with it. The 'chain' of threads I followed dead ended saying downgrade to get it work, but I don't want to do that. I had a hard enough time getting HardSPL 3.56 to install. Then I ran across Jockyw's CID unlocker http://forum.xda-developers.com/showthread.php?p=1837147 and found myself saying ooo and ahh! But, it won't work with ANY 3.xx HardSPL.
Is there a CID unlocker compatible with 3.56??
I'd love to have AT command mode stuff and etc. from jockyw's, but at this point I think I'll take whatever I can get without needing to downgrade.
I can't seem to find it now, but didn't there used to be a list of pre-cooked ROMs here somewhere?
I think what I'm aiming at is a fully patched / hacked 6.1 HTC ROM with everything fixed and no bugs. Preferably minus any bloatware. If it has recommended utilities pre-installed great, if not, no big loss. Did they ever finish hacking a video driver together? I lost track of that thread, and can't seem to find any current info.
I've been waiting for a working Linux distro for a HTC device for years, but I'm going to throw in the towel and make the best of what I can get on windows. I've spent over $3000 on these HTC devices over the years, but don't rely on them because of all the bugs. Once I get my Tilt patched up, I'm jumping ship and trading in my old ones for a G1.
Thanks for any help!
p.s. I DO have to CID unlock before I can install any other ROMs.. right??
p.p.s. Here's all the details if it's any help:
rom version 3.57.502.2 WWE
rom date 7/17/08
radio version: 1.65.21.18
protocol version: 25.88.40.05H
tri-color screen
KAIS1*0
SPL-3.56.0000
CPLD-8
.
.
Serial
image version 3.57.502.2
R 1.65.21.18
G 25.88.40.05H
D 3.57.00.00
Note: This is BEFORE I updated to HardSPL 3.56
Thanks again!
Click to expand...
Click to collapse
I'm sorry to tell you that this:
KAIS1*0
SPL-3.56.0000
CPLD-8
Is not hard spl and if you pda has hard spl installed is will say this:
KAIS1*0
SPL-3.56.Hard
CPLD-8
I received my replacement Tilt 4 days ago from At&t and it came with WM6.1 and spl 3.56.0000 and you are right I cant find anything to change that spl. I have tried to CID UNlock and I get the white screen, so I tried jump spl 1.56 and 1.93 and neither one of them worked. So now I'm stuck with this 3.56.0000, I sent Jocky a PM and He told me that he was looking in to it and that he will get back to me. So I have to wait. Or maybe someone will read this that has a fix for this issue and help us.
I just bought my Tilt too, it also came with 3.56 and WM6.1 but I had NO problems unlocking and flashing hard SPL to it.
Now, what happens when you run Jump 1.93? and are you running it directly from your main memory NOT from a SD card, and no SD card is in the phone?
If you follow the directions EXACTLY it will work.
1 Run Jump SPL from your main memory
2 tri color boot screen saying jump 1.93 should show up, with USB at the bottom
3 Unplug your device wait 30 sec and plug it back in
4 In Active sync on your PC disable USB connections (I've actually flashed spl's without doing this)
5 Now run the customRUU with the hard spl file you want to upload.
BerettaFreak said:
I just bought my Tilt too, it also came with 3.56 and WM6.1 but I had NO problems unlocking and flashing hard SPL to it.
Now, what happens when you run Jump 1.93? and are you running it directly from your main memory NOT from a SD card, and no SD card is in the phone?
If you follow the directions EXACTLY it will work.
1 Run Jump SPL from your main memory
2 tri color boot screen saying jump 1.93 should show up, with USB at the bottom
3 Unplug your device wait 30 sec and plug it back in
4 In Active sync on your PC disable USB connections (I've actually flashed spl's without doing this)
5 Now run the customRUU with the hard spl file you want to upload.
Click to expand...
Click to collapse
Yes I did all that I'm very familar with the process this is my 5th tilt 2 of them the CID Unlock run just fine and the other 2 I that to run jump 1.56 to get pass the white screen. But for some reason I cant get anything to work on this tilt. I even try to install the OG WM6.0 to try to downgrade the spl but that did work either. Do you have any other suggestions?
IIRC for me to run the CID unlocker program I needed to flash the SPL first.
What is happening when you are trying to run the Jump SPL files? It's just not making sense.
You need to flash Hard SPL 3.29 BEFORE you try to run the unlocker, you can't do 3.56 then try to unlock it. Once its unlocked then flash it with hard 3.56 if you so desire.
Also after doing the 3.29 spl you need the proper cracked radio flashed to allow you to unlock the device, are you skipping that step?
It sounds like your trying to do an SPL upgrade and NOT SIM unlock the device since that step comes after.
BerettaFreak said:
Also after doing the 3.29 spl you need the proper cracked radio flashed to allow you to unlock the device, are you skipping that step?
It sounds like your trying to do an SPL upgrade and NOT SIM unlock the device since that step comes after.
Click to expand...
Click to collapse
No what I'm trying to do is CID Unlock my phone but is not working I get the white screen. I have tried everything I know to get pass it. I'm not trying to install hard spl 3.29 or 3.56. I have to CID Unlock my phone first right? That is what I've always done before. I'm out of ideas.
What is on your phone right now?
Factory SPL?
Factory 6.1 rom?
If so you need to run Oli's Sim Unlocker and CID Unlocker exe, this will FIRST flash a 3.29 hard SPL to your phone, THEN then next step is to flash a cracked radio and then you can sim and CID unlock your phone. As noted before tho a CID unlock is NOT necessary, if your Sim unlocked and Hard SPL'd you can do whatever you want to the phone.
BerettaFreak said:
What is on your phone right now?
Factory SPL?
Factory 6.1 rom?
If so you need to run Oli's Sim Unlocker and CID Unlocker exe, this will FIRST flash a 3.29 hard SPL to your phone, THEN then next step is to flash a cracked radio and then you can sim and CID unlock your phone. As noted before tho a CID unlock is NOT necessary, if your Sim unlocked and Hard SPL'd you can do whatever you want to the phone.
Click to expand...
Click to collapse
Thank you very much for all your help BerettaFreak you are the man!
Heeey! Did my thread get hijacked?
Lol, Ok where to start..
skr_xd:
If you DON'T need to CID unlock, then the Newb instructions are a bit confusing. Why does it say to install HardSPL, then CID unlock?
What or why would I need to CID unlock separately? ..or is it the Security unlock bit, Or SuperCID that I'm still missing? There must be some point to it, Because Oli's Does HardSPL then SIM unlock, THEN CID unlock.
Vol22002:
I DID get HardSPL 3.56 installed. I used JumpSPL 1.56. DO remember to yank out the SD and SIM card. Note the very bottom of my post says those stats listed are BEFORE I installed HardSPL.
I still need some more help with finding a ROM, but I suppose that would be best addressed in a new thread, so I'll do that.
Thanks again!
Crogon said:
Lol, Ok where to start..
skr_xd:
If you DON'T need to CID unlock, then the Newb instructions are a bit confusing. Why does it say to install HardSPL, then CID unlock?
Click to expand...
Click to collapse
CID Unlocking is done by installing the Hard SPL, the Hard SPL's don't check the Carrier ID (CID) when flashing new ROM's.
Crogon said:
What or why would I need to CID unlock separately? ..or is it the Security unlock bit, Or SuperCID that I'm still missing? There must be some point to it, Because Oli's Does HardSPL then SIM unlock, THEN CID unlock.
Click to expand...
Click to collapse
SuperCID Set's your CID to 11111111, Security unlock removes an extra check when Flashing Radios to avoid you getting stuck on some radios.
Crogon said:
Vol22002:
I DID get HardSPL 3.56 installed. I used JumpSPL 1.56. DO remember to yank out the SD and SIM card. Note the very bottom of my post says those stats listed are BEFORE I installed HardSPL.
I still need some more help with finding a ROM, but I suppose that would be best addressed in a new thread, so I'll do that.
Thanks again!
Click to expand...
Click to collapse
Just follow all the steps in the Guide by mskip and post and problems you have there. Understanding is not a pre-requisite, with that guide, you can figure out what all the steps do later...
Simply put:
HardSPL / CID Unlock / Super CID - Allows ROM's and Radio's to be flashed.
SIM Unlock - Allows you to use a foriegn SIM card
Security Unlock - Avoids problems when flashing some Radios.
Ta
Dave
DaveShaw said:
SuperCID Set's your CID to 11111111, Security unlock removes an extra check when Flashing Radios to avoid you getting stuck on some radios.
Security Unlock - Avoids problems when flashing some Radios.
Click to expand...
Click to collapse
Hey, thanks for the fast reply Dave!
Ok, So I COULD still Security unlock it, If I could find a security unlocker that worked with 3.56.
The bit about problems flashing radios sounds a bit like something that happens right before your phone becomes a brick. Could you point me to a resource about problem radios or how to avoid them?
I actually prefer to leave the radio alone, if I can get away with it. I just want a patched up ROM, as I mentioned earlier and in my new thread.
Anyway, If I end up needing to replace my radio, how do I avoid 'problem ones'. I understand that some radios simply don't work with some ROMs, but you seem to be eluding to something different here.
Thanks again!!
Crogon said:
Hey, thanks for the fast reply Dave!
Ok, So I COULD still Security unlock it, If I could find a security unlocker that worked with 3.56.
The bit about problems flashing radios sounds a bit like something that happens right before your phone becomes a brick. Could you point me to a resource about problem radios or how to avoid them?
I actually prefer to leave the radio alone, if I can get away with it. I just want a patched up ROM, as I mentioned earlier and in my new thread.
Anyway, If I end up needing to replace my radio, how do I avoid 'problem ones'. I understand that some radios simply don't work with some ROMs, but you seem to be eluding to something different here.
Thanks again!!
Click to expand...
Click to collapse
To Security Unlock, just follow this guide: http://forum.xda-developers.com/showthread.php?t=361236
Then upgrade to HardSPL 3.56 again.
Security Unlocking is done by setting a flag in the NAND. It's permanent (unless you re-lock) and there are no comptability problems once it is set (you need to use a special Hard SPL to set it first though).
EDIT:
There is no list of known bad radio's - only the "Radio from Hell" 1.65.17.10 - but another Radio from hell could appear any day
Ta
Dave
Thanks for clearing that up Dave.
I think I'm going to opt to ignore the security unlock, since it sounds like it's on an 'as needed' basis.
I have 'batter fish to fry' at the moment. I'm grinding gears trying to figure out HOW to figure out which ROMs I should be looking into, in my other thread.
By the by guys, I was joking about the 'hijacked thread' thing, I'm sure somebody will find the info useful.
Just when i though I had this all figured out and was about to Flash my first ROM.
I have read and re-read the flashing wikis and am still confused.
If your on WM6 then you need to use Jockyw2001's Kaiser SuperCID and Security Unlocker v0.1 right? But if you are on WM6.1 then you use Olipro's Kaiser SIM/CID Unlocker & Changer right?
Well I am currently on WM6 pro and dont want to upgrade to 6.1 just to use Olipro's program. So I would go with Jocky's right. Then people say you need to flash a HardSPL first before doing the SuperCID and Security Unlocker. But then in Jocky's directions it says Note that the security unlocker does not work with "SPL-3.28.Hard" and "SPL-3.29.Hard".
So what SPL do you start with.
And I know Dave already told me this earlier that since I have an AT&T Tilt and I am with AT&T service then I dont have to worry about SIM unlocking obviously. So can I skip the whole CID/SUPER CID/SECURITY UNLOCK routine. Can I just Flash HardSPL 3.29 or 3.56 and then start playing with ROMS till my hearts content or is all the security stuff really that neccessary?
So I am lost once again. Wow. I dont know why I am not getting this.
P.S. On another note, I am using AT&T Tilt with shipped ROM running WM6 pro. I have about 40-50 programs installed on it. When first setting up my phone I did the soft reset which supposedly gets rid of the bloatware. Anyways, with all my programs and it being the stock ROM I still have 62MB free PROGRAM RAM. I do however only have like 30MB Storage RAM. But 62MB of free PROGRAM RAM. I see people with naked ROMS that only get like 55MB of free PROGRAM RAM, is my phone like magic or something? Just curious as to how this may be possible.
asofiker said:
Just when i though I had this all figured out.
I have read and re-read the flashing wikis and am still confused.
If your on WM6 then you need to use Jockyw2001's Kaiser SuperCID and Security Unlocker v0.1 right? But if you are on WM6.1 then you use Olipro's Kaiser SIM/CID Unlocker & Changer right?
Well I am currently on WM6 pro and dont want to upgrade to 6.1 just to use Olipro's program. So I would go with Jocky's right. Then people say you need to flash a HardSPL first before doing the SuperCID and Security Unlocker. But then in Jocky's directions it says Note that the security unlocker does not work with "SPL-3.28.Hard" and "SPL-3.29.Hard".
So what SPL do you start with.
And I know Dave already told me this earlier that since I have an AT&T Tilt and I am with AT&T service then I dont have to worry about SIM unlocking obviously. So can I skip the whole CID/SUPER CID/SECURITY UNLOCK routine. Can I just Flash HardSPL 3.29 or 3.56 and then start playing with ROMS till my hearts content or is all the security stuff really that neccessary?
So I am lost once again. Wow. I dont know why I am not getting this.
Click to expand...
Click to collapse
There is a Hard SPL 1 by pof. Flash that first then follow Jocky's instructions.
Also the OliPro Security unlock isn't permenant, next time you flash a Radio it's gone.
Ta
Dave
Ok so Flash the Hard SPL 1 by pof
Then follow Jockys directions in using his Kaiser SuperCID and Security Unlocker v0.1
Then Flash either HardSPL 3.29 or 3.56. WHichever I choose?
Then go crazy with playing with different ROMS.
P.S. So every time you Flash a HardSPL it overwrites the previous one? Or do you have to get rid of a HardSPL first before putting a new one on?
asofiker said:
Ok so Flash the Hard SPL 1 by pof
Then follow Jockys directions in using his Kaiser SuperCID and Security Unlocker v0.1
Then Flash either HardSPL 3.29 or 3.56. WHichever I choose?
Then go crazy with playing with different ROMS.
P.S. So every time you Flash a HardSPL it overwrites the previous one? Or do you have to get rid of a HardSPL first before putting a new one on?
Click to expand...
Click to collapse
Flashing a new SPL overrides the old one.
You said before you were happy with WM6.0, if so use either the pof Hard SPL v1 or the jockyw Hard SPL v1.1 (Part of the security unlock); if you are using WM6.1, use one of the jockyw or cmonex Hard SPL 3.**. Using the wrong version won't break your phone, but Windows will randomly freeze.
Ta
Dave
Thanks again Dave for helpin me out and not tearing me a new one. But just one last question.
If I find a new ROM that I want to Flash and it uses WM6.1 then I have to make sure that I flash a HardSPL 3.xx before flashing that new ROM, is that what ur saying?
i got elfin and i want to ask if it is any way to flash rom in bootloader mode,i want just to got my htc working again and my device is stucked at bootloader showing in right top corner RUU and on left IPL And SPL numbers.
ms2405 said:
i got elfin and i want to ask if it is any way to flash rom in bootloader mode,i want just to got my htc working again and my device is stucked at bootloader showing in right top corner RUU and on left IPL And SPL numbers.
Click to expand...
Click to collapse
hey, i just took a brief look in the elfin section. Go there and look at the stickies, there are guides for un bricking yoiur elfin and a good guide on how to correctly hardspl and flash....DO READ THEM (and you normally should flash a rom from bootloader in any case )
If you dont want to hardspl, then try the uspl way. You didnt say what rom you had tried to flash or wot you have done to get it stuck in bootloader.
Also are you using vista or xp on your computer?
i'm using xp on my comp,i got to bootloader because i tried to flash some roms and when i tried last time flashing onyx one it showed me error message and then started the problem.
ok, did u hard-spl sucessfully? what is you ips/spl shown on bootloader?
IPL is 2.26.0002
SPL is 2.26.0000 and as i said in right top corner RUU,
i've tried to flash it from sd card,but it ain't worked andlooked at goldcard method and i haven't got another winmo devic and don't know somebody who has,please help me to unbrick my phone,it was both from orange uk.
ms2405 said:
IPL is 2.26.0002
SPL is 2.26.0000 and as i said in right top corner RUU,
i've tried to flash it from sd card,but it ain't worked andlooked at goldcard method and i haven't got another winmo devic and don't know somebody who has,please help me to unbrick my phone,it was both from orange uk.
Click to expand...
Click to collapse
Please have a look at post 3 from here : http://forum.xda-developers.com/showthread.php?t=408637
Is this what you have tried doing previously?
Did you unlock your elfin first if it is locked on orange network?
If you cant get it working after trying this, go back to first link above and flash back an original stock rom, at least ur device will be working again!!
ps when u hardspl and tried to flash, did u disable antivirus on PC, and disconnect all other non essential usb devices? This is an commen cause of bad flashes, also try other usb ports, 2 of mine i cant flash on, 2 i can (which is wierd) - (i have experienced this myself).
If any of this doesnt help, as for help in the elfin section, but DO describe all your steps properly and fully and enclose links of roms tried etc so someone with an elfin can see what you have donw and save unnecassary posts etc.
mate,the link you gave me is that when i upgraded my elfin when it was working, i don't know what you mean about unlocked it is sim unlocked what about cid i really don't have idea,because i couldn't connect to mtty,please can you give me the link for original stock rom for my elfin,because i haven't done backup and i downloaded one but i don't know how to put in when i got in bootloader only and can't connect acivesync please tell me how to this aswell,PLEASE HELP ME UNBRICK MY ELFIN!!
Have you resolved this?
Search and download a stock rom from HTC or from here, use the search and wiki, you will find one there.
When you plug in ur elfin into the computer and put it in bootloader, do you see "USB" on the screen along with ur ipl and spl?
You should, and if you do you should be able to flash the stock rom on.
to all who had been encountered this need you help...
palm treo 750 unlocking..
i had been unlocked the phone using cheetah unlocker
flash SPL successfully
unlock radio successfully
and put herm unlocker at prog.files and run it..it was also successful
when i enter now un-accepted sim it says that....
you have tried 91 times .please wait until time out
i was powering without touching it for almost 4 days but still 91 times
i also tried reseting it still that problem...
anyone out here who could help me in order to put the unlock code so that i will request its codes....
just want to update this trade,admin and to all
phedz said:
just want to update this trade,admin and to all
Click to expand...
Click to collapse
updating..............................
any one.......
I've had this issue too, and to date, I haven't found a solution. If you do find a solution, I'm grateful for it.
i had been unlocked the phone using cheetah unlocker too ...
bootlogo:
By Olipro & Cmonex
IPL-SSPL-OliNex
By Olipro & Cmonex
SSPL-1.01.OliNex
flash SPL successfully
unlock radio successfully
and put herm unlocker at prog.files and run it..it was also successful ...
but "un-accepted sim" ...
"direct bootlogo" (reset+media):
CHEE100
IPL-0.20
CHEE100
SPL-1.40.OliNex
start "cheetah unlocker" :
bootlogo ia again:
By Olipro & Cmonex
IPL-SSPL-OliNex
By Olipro & Cmonex
SSPL-1.01.OliNex
... its OK ?