When I was upgrading my 3630 to wm2002 yesterday, I got an error saying 'communication port not found', and now it won't boot up..I can't access the backlight, and all I can see (from an angle) are 2 white horizontal bars and a host of vertical 'pinkish' bars that flash from time to time. I tried re-syncing it, and Vista doesn't recognize that it is attached. Is it a paperweight now, or is there something I can do to fix it? Thanks in advance for any help you can give me.
Related
Hi everybody,
i have flashed the WM6 underground edition a couple of weeks back. Now i wanted to downgrade to WM5, but without success. I am using IPL/SPL 2.21. After starting the ruu upgrade software the Wizard switches to boot mode. So far so good.... But then nothing happens anymore and after a minute or so the software quits with error 260.
Any hints what to do ??
I have the newest Activesync installed.. I even cannot flash any other Wm6 rom.
Any help would really be appreciated !!!!
Best regards
Batman08
When you reboot your phone, post exactly what version IPL and SPL you see.
Didn't someone once post that there was a difference in USB cables....Grasping at straws, but just a thought!
Hmmm... do you hear the active sync connection bell ring when it reboots into bootloader? At the bottom of the screen, do you see the letters USB near the left hardkey?
Might try another PC, or even a different USB port on the same machine. Sounds like the USB is acting up.
After the phone reboots i can see IPL/SPL 2.11.
I can hear three bell rings with the same low frequency. To
me that is not correct as the connection bell ring should be two tones ?
I can see "USB" on the left side of the Wizard's screen.
I also tried different cables, but no success.
I am using WIN XP with SP2. Upgrading worked flawless
some month back with WM5.
The only thing i had to change was ActiveSync 4.5 as WM6 is only
supported there.
Any hint ???
batman08 said:
After the phone reboots i can see IPL/SPL 2.11.
I can hear three bell rings with the same low frequency. To
me that is not correct as the connection bell ring should be two tones ?
I can see "USB" on the left side of the Wizard's screen.
I also tried different cables, but no success.
I am using WIN XP with SP2. Upgrading worked flawless
some month back with WM5.
The only thing i had to change was ActiveSync 4.5 as WM6 is only
supported there.
Any hint ???
Click to expand...
Click to collapse
ERROR [248~260] : UPDATE ERROR
This error occurs when there is an “open port error” before upgrading the CE ROM image.
Solution: You can reset the device and run RUU again. If you still encounter an “OPEN PORT ERROR” again, reset your computer and try again.
This is taken from the redme inside the RUU
Good Luck
Put the phone into bootloader mode, kill WCESCOMM.exe from process list, attach Wizard, let it install driver, open up RUU and (hopefully) flash.
Also make sure you pull out your SD card while you try to flash your phone.
@neonkoala:
You made my day !!!!!!!! it worked flawless.... Thanks a lot !
After I tried to upgrade the rom to WM6, my JAMin got stuck at bootloader. After that, I tried to flash WM5 roms without success and suddenly (after a reset) the screen became white with some horizontal and vertical lines constantly moving. I discovered that it was only the screen that was garbled as it still connected to PC, so I installed (without seeing anything on my JAMin) the NVID ROM trying to restore it. It installed sucessfully, but the screen remained garbled with the white background and random lines. I know it was sucessfully installed because I heard the typical "welcome" sound before configuration.
Do you know any way to restore the screen? Or must I send it to I-Mate to repair?
You can try and reattach the screen cable to the rest of the device, but this will boid any warranty you have, and may damage your device further. If the device is under warranty, I would suggest flashing the ROM the device came with (unfortunately the FTP server is down at the moment, so it might take some fishing around for) and sending the device back to get repaired properly.
mpmf said:
After I tried to upgrade the rom to WM6, my JAMin got stuck at bootloader. After that, I tried to flash WM5 roms without success and suddenly (after a reset) the screen became white with some horizontal and vertical lines constantly moving. I discovered that it was only the screen that was garbled as it still connected to PC, so I installed (without seeing anything on my JAMin) the NVID ROM trying to restore it. It installed sucessfully, but the screen remained garbled with the white background and random lines. I know it was sucessfully installed because I heard the typical "welcome" sound before configuration.
Do you know any way to restore the screen? Or must I send it to I-Mate to repair?
Click to expand...
Click to collapse
Hi frd,
I have exactly the same problem!
Nothing , only the f*** white screen!
I can browse the device via active sync, can rcv calls but the white screen.
I have checked the ribbon connector of the LCD and make reflashing some ROMs but nothing.
I still wondering is it hardware or software problem!
Please let me know if you have progress!
Thanks
G.
Try to replace LCD module, I think thats right way.
It will be a hard ware problem. Probably the ribbon cable as the screen is showing something so it must be working at least a bit.
Hello,
i have the same Problem with my QTEK S200.
First i changed the Rom and it worked perfectly for two days.
Then i had to change my Sim card and after that the problem came again.
I tryed a lot of times to reflash the rom but the problem persist.
How can it be that it worked again for some days ?!
is it the touchscreen of the lcd unit i have to replace ?
is it possible to do it by my self ?
thanks for your help !
Hi everyone.
I had a similar problem an hour ago (Qtek S200 G3):
I Upgraded to a 6.1 rom and then to another, after that my device was stuck in bootloader(3 colour screen). Any 6.1 rom that I tried would install, but after installation device always boot in to the 3 colour screen.
I tried this original shipped rom http://files.mail.ru/HZUAH1 (it's WorldWidwEnglish) (to download just click the link "скачать" or the file name RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
) and it installed!!! It TAKES A WHILE TO INSTALL!!! But it worked!!!
May want to try it.
Hope this helps.
hello,
picture on screen was immediatly clean again ( bootload image ).
it was impossible to change the rom because i have a G4 model.
i flashed the rom with another french rom for G4 and it worked perfekt.
now i tried to remove the battery again for 3 seconds and now i have the same problem again. really strange ....
i tryed the same procedure again but no success.
I reinstalled differents rom's again starting always installation from bootloader.
After about 10 new installations i've clean picture again.
now i'll not put off, restart, or take of battery till one of you know what's the problem.
Thank you for your help !!
are you guys sure its not an intermitant hardware problem, it sounds like it to me. if yu were able to get a clean picture for a short time and now its white again, it cannot be the rom? As for replacing it, nothing is impossible and there is always ebay and google
QTEK S200 G4 CID unlock
How can I CID unlock a device that need´s that to upgrade the Rom?
Is there already any program that , Lockwiz dont do the job, can performe the unlock?
Thank you.
For G4 CID unlocking, you need to user Hard/Soft SPL.
same problem
my imate jamin got the same problem. it happens only and only when I remove the battery and when I leave it to charge for 1-2 days the LCD works again and show clear pic. any suggestion? activesync and &... are all ok!
Well, i upgraded to windows Mobile 6, but haven't removed the batterie anymore.
But i'm able to put it off now, what was impossible before.
Hello girls and boys,
yesterday my TC first stuck in tricolor screen and shows
POLA100 RUUNBH
SPL-1.25.0000
CPLD-2
and downwards: USB or SERIAL
It happened as I tried to flash back the original Radio for it. The update monitor showed ERROR 262 (0%), before that I had already installed signed_RUU. for original German WM6-ROM and it worked fine exept the decreasing GSM connection.
After that I searched here the whole night for solutions but none of them (MTTY, Radio Murata, UN-SPL, flash Radio or OS from microSD) helped.
I guess it's all I am able to!
Maybe one of you guys can help me?
Or can anybod tell me whether my TC is dead?
Can anyone tell me the meaning of:
POLA100_____________RUUNBH
SPL-1.25.0000
CPL-2
Thats what my tricolor screen shows!
Maybe someone can tell me where I can get the original German RUU....ship.exe for Polaris.
Did you install HardSPL before playing around with your phone?
Yes I did, and it worked fine exept the bad radio issue.
My TC started to hang as I tried to get back.
Hi everyone I am very new at all of this, but I have a problem. I was updating my xv 6800 titan with the windows mobile 6.1 update from verizon and i accidentally unplugged the usb cable and now i have the rgb screen that says TITA100
SPL-2.07.008
CPLD-9
and ruunbh in the top right hand corner and it does not connect to active sync or anything is there anyway i can fix my phone? thank you very much
Have u been able fix, i have same problem with rgb screen. Mine caused by xv6800 timing out and going black like 10% into updating. Please post how u fixed.
Could it be because i'm using vista?
Hi there guys .
I've been searching and searching, and trying and trying, but I can't seem to get past this Error [262] when I'm trying to upgrade my ROM or Radio (HTC Diamond).
What I'm doing is this basically:
I downloaded DiamonCustomRUU.exe, put it in a folder with the radio/rom (say Diamond_Radio_1.00.25.05.nbh), I connect my HTC Diamond to my pc via usb, activesync is on, I start up the RUU, go through all the steps, then at the end when the update 'starts', my phone goes off, starts up in the 4 coloured screen, activesync stops, then my phonescreen turns grey with the progress bar (stuck at 0%), and on my laptop there's a progress bar as well. It does nothing, and after about 5 minutes, I get the Error [262].
I reinstalled Activesync, but no changes. I installed HardSPLL though. I tried another USB-port, doing it without my firewall on (someone suggested it, yes I'm desperate)... I have no idea where to go from here.
Can anyone help? (sorry if this is the wrong section..)
Love
Had the normal (signed)SPL instead of the hardSPL. Can be locked