Hi,
I have just purchased an O2 XDA IIs PDA / Mobile Phone. It works fine (after removing the O2 Active thingy). The only problem is that when I try to switch on BlueTooth (or try accessing BlueTooth Manager) i get the following message:
Bluetooth Radio failed to turn ON due to insufficient driver memory available. You must perform a normal reset before you can turn ON the Bluetooth Radio
Click to expand...
Click to collapse
I did a normal reset a couple of time but no success. Any help? and any idea what the driver memory is??
I'm having one major problem that I've been unable to solve. Every so often the bluetooth stops working and the sound locks giving error=2. Bluetooth reports "failed to turn on due to insufficient memory". If I try to increase the volume it goes back to 0. The only solution is a full hardware reset. It's happens so often I've transferred all the cab's onto a separate sd card so I can reinstall the lot without a PC.
I have a feeling it is USB related as it seems when it's stuck into a port it can on occasion initiate the problem.
The only way I've managed to sort the issue was by upgrading the bluetooth to a newer version (broadcomm_bt_stack.CAB 1.7.6) via a hack found on one of this forum, however while the sound then works the bluetooth is off completely probably because registry settings are using the wrong port etc.
Here's a list of the PDA spec:
OS: 5.01, 20061016
ROM: 1.10.15
Firm: 3.0
Bootloader: v2.17
Bluetooth: Broadcom 1.7.1 Build 8700
I have attached the bluetooth registry values (before I try to update the stack).
Any ideas???
hi; can somene tell me how to solve my problrm, my spv c600 always on bootloader after bad unlock, i try to reflash by upgrade rom , but connection is not etablished by active syncro !!
how to forced my phone for connection with soft upgrade!!
same here, no matter what it stays in bootloader
active sync will not connect in bootloading mode. if you still hear the connection sound (the sound you hear plugging in any usb device)on your pc then it is connected to the pc and can flash a new rom
follow this guide exactly (proabbaly were doing this now just finish from where you left off)
http://karhoe.net/guide-upgrading-htc-tornado-to-windows-mobile-6
I hear the USB connecting sound, but tera Term says canot open
Before you try tera term, go to connection setting of Activesync and uncheck 'Allow USB Connection', otherwise teraterm cannot connect your phone.
thacen said:
Before you try tera term, go to connection setting of Activesync and uncheck 'Allow USB Connection', otherwise teraterm cannot connect your phone.
Click to expand...
Click to collapse
Still no go
did u ever find a solution?
In bootloader mode activesync cannot connect. But you can flash rom directly using ROMUpdateUtility in this mode. Best thing is try with original factory rom.
Another possibility of going to bootloader screen on every startup could be of hardware problem. I also faced similar problem frequently.. but I resolved the problem. My case was because of my camera button.. it actually is not working properly and sometimes remain stuck in, then my handset goes to bootloader on every startup..In that case i just pull it up using some sharp edge.
So, check for any hardware problem to, sometimes cleaning could also help.
hi
my phone was weeks ago in service. after new motherboard they install fresh software on it. but now i cant turn bluetooth anymore on. it gives me error:
the bluetooth radio failed to turn on due to insuffcient driver memory available. you must perform a normal reset before you can turn on the bluetooth radio.
it bluetooth works after hard reset. if i install spb wireless monitor it wont work anymore. but before service it was working on my phone. same soft.
how to get it work? i need to use bluetooth.
Welcome to forums
As here we dedicate only to HTC devices you won´t get too much atention
better if you try here:
http://cellphoneforums.net/lg/
Good luck,
Can anyone please help
My x51v has decided it is unable to switch on bluetooth with an error message "due to insufficient driver memory space" with advice to reset.
All was well untill recently though over time I have had this message on occasion but cleared on retry.
Bluetooth connection is important to me so advice welcome.
Thanks