Related
Ok i have up graded to wm5 from 2003... Can get TT5 to work.. so give up now would like to go back to 2003..... how do i do this I did back up, but when i go to restore it I get erro getting devicedata in one of these cmd boxes... I would just like to go back to when it worked Thanks for you help
John
Used awizard to revert back the OS from ver2 to ver1. It has unexpected error during the "w" option and the device is hung for a long time. Did a soft reset, and after that it only shows upto i-mate booting screen and sits there. No activesync is detected now of course and is there anything to recover this. Please...
Press Camera+softreset, you will enter bootloader, try to get you original ROM and flash. Hope this can help you!!! BR
This will work. I had the same thing with my 8125 once. Get it to the bootloader screen (Camera+SoftReset) and connect via USB to your PC. Run your RUU and it will work.
I had a bad experience with aWizard and figured I was not educated enough and decided to not mess with anything but an RUU for now. Even still I don't mess with ROMs anymore. Not worth the risk/headache.
Let us know if you recovered.
Hi everyone. I am in need of assistance with shelltool. I've been flashing ROMs for quite some time and this goes beyond the scope of typical upgrading. I apparently had a bad flash happen and need some help correcting it. The OS appears to work fine, except some applications .cab installers exit before asking device or storage card. I have attempted to load the EnableRapi.cab and Cert_SPCS.cab; however, they exit almost instantly after starting them.
I had this situation happen once before and I was able to oddly enough try to load the original T-Moblie ROM through shelltool (didn't install at all), then try NBD 8.3. which brought me to a boot loader screen after doing a hard reset, but didn't install NBD 8.3. So far I'm not having much luck in recreating the experiment.
Is there a way to force a Wizard into bootloader mode using shelltool or some other utility? I can restore the device if I can get that far.
it's time for my first post
Hi, have been reading this forum for about 3 month and i enyoy it and learn a lot. Have been try about 7 roms and like all. It's time to payback.
Yo can enter bootload by pressing and holding the voice command button and then softreset, keep holding the voice command button util you reach bootload.
Other thing you can do is run the original rom by its executable program not using shelltool.
Good luck
Awesome! That rescued my phone. You saved me quite a bit of time in getting my phone back to a working state. You've more than given back!
Dezl0ck said:
Awesome! That rescued my phone. You saved me quite a bit of time in getting my phone back to a working state. You've more than given back!
Click to expand...
Click to collapse
no problem, that's why we are here for, to help each other
Help, Stuck at multicolor screen. XDA Mini S
Dezl0ck said:
I can restore the device if I can get that far.
Click to expand...
Click to collapse
Please tell me how did you restore your phone? i am flashed touchflo rom to my phone and some how it is stuck to the multicolor screen.
Can you help me out?
Thanking you in anticipation.
1 put phone into bootloader by pressing and holding camera button+reset hole. Keep holding the camera button untill you see the tricollor screen.
2 plug the phone into the computer (wait to hear the noise that it found hardware
3 Flash a rom you know worked (maybe your original/ maybe someone elses... maybe even mine )
4 wait untill the flashing finishes and "Tap Screen..." appeares before unplugging.
(If you have a G4 then I advise you to flash the original rom, or make sure your ipl/spl is propper. check the G4 forum to be sure, or ask Mestrini - The creator of the Wizard service tool. I believe he has a G4 and knows more about it than most)
Happy Flashing
Randomly get Update/Connection errors.
Thank you very much for the response.
Unfortunately, i am still not able to flash the ROM. I did the follwoing steps, can you please help me letting me know, where m i wrong?
I restarted my PC.
I did Reset my PDA, by removing and placing the battery.
then i boot the PDA, it always boots to the TRICOLOR Screen.
afterwards, i tried to flash following ROMs
Xda_Minis_Upgrade_v2.21.4.101.exe [the oringal one, used to be working since long]
SNN_Version_3.0 [i flashed this, some days ago and worked fine for me]
SNN_3.0_FULL_version [the ROM that caused the problem]
BUT no use, i randomly get following errors:
ERROR [262] : UPDATE ERROR
ERROR [274] : CONNECTION
and some other errors.
Pleaaaaaase some one help me.
Thanking you in anticipation.
OK
I've always had troubles flashing radios for some reason, I've managed to just not do it but now with Duttys 6.1 out I really need some help
- I've flashed Duttys latest successfully
- I've flashed HardSPL
- But whenever I flash the radio (1.64.08.21) I get a connection error at 99%!!
Now I can still get into the phone using mtty and the boot command.
Am I doing something stupid -- Any help gratefully received!
Alex
ps - I have a UK o2 XDA Stellar
I'm a newbie been here with a AT&T Tilt less than a week and I promise I'm reading, but I'm having the exact same problem. Flashed Duttys dual V4 as my first try last Tuesday without a problem and of course be a crazy new guy I wanted his newest work. So I flashed Duttys 6.1 today and I guess I just can't figure out how to flash radios, because I've tried 2 now and both error out at 99% and I too have to use mtty to get back into the phone. I'll keep reading, but if someone could tell us new guys what the heck we are doing wrong that would be great.
PS I'm glad to be here and this looks like a lot on fun thanks for having me and look forward to helping out someday.
JMan
Hey Alex! I figured it out Brother! Do this and you should be able to upgrade your radio. I was using JumpSPL1.56-KAIS run from my device and I was running into the same problem everytime I tried to upgrade my radio. Would get to 99% and then would error out. So I followed these steps taken from a number of different post and put together until it worked!
1) Make sure you have JumpSPL1.56-KAIS somewhere on your device the file for me is in "my docs" on my Tilt.
2) Run kaiser-HardSPL from your PC with your device hooked up via usb with the green act sync icon. Once you get to the white screen of death on you device, stop unplug you device and soft boot it via your stylus and the reset button. Leave your pc alone right where it stopped in the kaiser-hardspl screen. "should be to the point where it says unplug and replug in your usb you should have the tri color screen press enter to proceed"
3) Now set your connection settings in active sync to not allow usb connections.
4) Now plug you device by in via usb and run Jumpspl1.56-kais on your device. When it has the tri color screen and says usb, unplug usb and plug back in.
5) Now back in the kaiser-hardspl window, continue on with the on screen directions. This should now install hardspl just like the rom or roms that you might have already installed and will say finished.
6) The device should reboot.
7) close the kaiser-hardspl window and let you device fully reboot.
8) Once it is fully rebooted follow these directions: Perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up
9)Now run your radio update and it should go through without erroring out at 99%. It will stay at 99% for a bit then jump to 100% success!
My Tilt is working great now with sound and everything. Have not tested anything else yet, came right here and started to let you know what I did to get radio installed.
So now I'm running Duttys WM6.1 newest release with radio 1.64.06.
Call me crazy and sure I know I might have taken more steps than I needed to, but I got it working.
Hope this helps you.
Take care,
JMan
First, are you using a 6.0 rom or a 6.1 rom? If you are using a 6.0 rom you cannot flash any of the 6.1 radios and vice versa. Also, if you have hardspl installed, why would you need to use jumpspl. I have never used jumpspl and I promise I have flashed 50+ times counting, roms, radios and splash screens.
I believe that was my problem, I was never able to get Hard-spl installed and I was using jumpspl to install the 2 roms that I have installed since I got my tilt a week ago. The method I used above allowed me to get hard-spl installed and then I was able to install the radio rom. I am using Duttys WM6.1 rom.
JMan I want your babies!!!
Ok I had actually done everything upto the final step (holding the camera button after a soft reset) but that made it possible to flash the radio just as you described.
So many thanks for sharing your solution!!
Alex
jmandss said:
Hey Alex! I figured it out Brother! Do this and you should be able to upgrade your radio. I was using JumpSPL1.56-KAIS run from my device and I was running into the same problem everytime I tried to upgrade my radio. Would get to 99% and then would error out. So I followed these steps taken from a number of different post and put together until it worked!
1) Make sure you have JumpSPL1.56-KAIS somewhere on your device the file for me is in "my docs" on my Tilt.
2) Run kaiser-HardSPL from your PC with your device hooked up via usb with the green act sync icon. Once you get to the white screen of death on you device, stop unplug you device and soft boot it via your stylus and the reset button. Leave your pc alone right where it stopped in the kaiser-hardspl screen. "should be to the point where it says unplug and replug in your usb you should have the tri color screen press enter to proceed"
3) Now set your connection settings in active sync to not allow usb connections.
4) Now plug you device by in via usb and run Jumpspl1.56-kais on your device. When it has the tri color screen and says usb, unplug usb and plug back in.
5) Now back in the kaiser-hardspl window, continue on with the on screen directions. This should now install hardspl just like the rom or roms that you might have already installed and will say finished.
6) The device should reboot.
7) close the kaiser-hardspl window and let you device fully reboot.
8) Once it is fully rebooted follow these directions: Perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up
9)Now run your radio update and it should go through without erroring out at 99%. It will stay at 99% for a bit then jump to 100% success!
My Tilt is working great now with sound and everything. Have not tested anything else yet, came right here and started to let you know what I did to get radio installed.
So now I'm running Duttys WM6.1 newest release with radio 1.64.06.
Call me crazy and sure I know I might have taken more steps than I needed to, but I got it working.
Hope this helps you.
Take care,
JMan
Click to expand...
Click to collapse
You are the STAR! Trillions of thanks. Solve my problem!!!
I love it when when the new guy can help out! Glad it worked guys, and thanks to all the old pros around here for allowing us to read so we can try and help ourselves out.
Take care,
JMan
I think I have fallen in love with this thread. This is truly nice to see guys. Keep up the great work.
i've the same problem, but when reboot Appear immediately hardspl, but i can't re-install nothing !
please help me
I don't want to miss mi tytn
pedro_se_rooot said:
i've the same problem, but when reboot Appear immediately hardspl, but i can't re-install nothing !
Click to expand...
Click to collapse
You need to use MTTY to get things going for you again, here is the thread to get mtty:
http://forum.xda-developers.com/showthread.php?t=371154&highlight=mtty
Search around and see if you can find the step by step to use it, might even be a how to text file in the zip file not sure. This should get you back on your way.
Can someone locate the step by step to use mtty for this man and put it in this post?
Have a good one,
JMan
Not a good day for the Wolfpack, Damn Tarheels!!
Hi everybody,
i got a XDA Orbit 2 and today i tried to install SPB Phone Suite.
During install it asked for a Softreset, which i did...
After that i refused to boot and keeps hanging at the o2 Bootscreen.
It totally freezes, regardless if i pull any cable, remove the sd-card etc..
So i thought i'd a hardreset once again, but that one didnt work at all.
The Restore lasts maybe 10 secs (with and without sc-card), then asks for another boot and im again where i startet, the o2 bootscreen.
Any chance i get it working again?
Like somebody else recommended flashing it with either another rom or the original one, which i might d/l somewhere.
Then again, any Flash-HowTo starts with an ActiveSync Connection.
Since my Device wont boot at all, the ActiveSync Connection wont be established...
Any helpful Advise highly appreciated :-/
regards...
You should be able to manually put it into the boot loader. I'm not familiar with you phone so you will need to research that.
***Update**** Try this; "turn your phone on press and hold the two buttons on the upper left and right side from your naviwheel and press the resetbutton with your stylus"
http://forum.xda-developers.com/showthread.php?t=366303
hrm, pressing the upper left/right buttons and reseting it doesnt do anything.
regarding google im the first human ever trying to get the htc touch cruise into bootloader mode.
i keep researching, thx for ur effort tho
Manually getting into the boot loader will allow to establish a link to your PC in order to re-flash. Like I said, I'm not familiar with your phone....
yup, i noticed some more users here own an Orbit2.
So i hope somebody is able to enlighten me, before i brake my fingers while trying to press all buttons same time and then somehow hit the reset button, hehe.
ok, i managed to get into bootloader.
some more detailed research helped me there, actually inside this board :-/
now lets see if HardSPL makes me happy.
tx again for ur time
I have an Orbit 2,
To Hard reset and delete everything from your phone and then let the rom reload everything back to factory settings, do the following.
1. Remove SD card
2. Hold down the 'Windows Icon' Button and the 'OK' button at the same time and keep them held in.
3. While still holding in the above 2 buttons, use the stylus and press the reset button in and then release it but you must still keep the 'Windows' button and the 'OK' button still in until you are prompted with a menu.
4. Once the menu appears: press 'Send' button to reset and reload rom or any other button to cancel.
I have done this procedure a few times now and is quite safe, especially after loading a crap piece of software that totally knackers up my Orbit 2.
I hope this helps you out........
Good luck
Tried that before and it worked out before also.
This Time the complete recover-process lasts only 10 seconds and then the Boot doesnt work anymore either.
Dunno why the hardreset aint working anymore.
Regarding the Flashing:
I managed to get into Bootloader and see the following Information:
POLA200
SPL-1.25.0000
CPLD-2
Serial.
Then i plug in the USB-Cable and start the Update-Utility.
After following each step i get the following error:
Error 262: Update Error
Saying it has encountered communication Errors and asks me if i want to recover...
Im running VistaSP1, maybe thats a reason?
Try this for your Vista issue. It worked for me the first time. Although I don't know if SP1 has any effect.
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27 This was for Hermes also....
Updating the USB-Driver didnt help .
Using a XP VirtualPC didnt work out either, hehe.
Ill try tomorrow on a XP Machine, thanks for ur time once more.
Im not that desperate anymore, hehe.
Damn, now im using a Windows XP Machine (incl. all Updates) with ActiveSync 4.5, and still get the [262] Update Error.
Seems its seriously damaged :-(
One Question:
Did you installl phone-suite on a cooked rom, or on the original o2 rom?
i got the same freezing problem on my touch with a cooked rom. with the original rom i got no problems.
..
ploep said:
Hi everybody,
i got a XDA Orbit 2 and today i tried to install SPB Phone Suite.
During install it asked for a Softreset, which i did...
After that i refused to boot and keeps hanging at the o2 Bootscreen.
It totally freezes, regardless if i pull any cable, remove the sd-card etc..
So i thought i'd a hardreset once again, but that one didnt work at all.
The Restore lasts maybe 10 secs (with and without sc-card), then asks for another boot and im again where i startet, the o2 bootscreen.
Any chance i get it working again?
Like somebody else recommended flashing it with either another rom or the original one, which i might d/l somewhere.
Then again, any Flash-HowTo starts with an ActiveSync Connection.
Since my Device wont boot at all, the ActiveSync Connection wont be established...
Any helpful Advise highly appreciated :-/
regards...
Click to expand...
Click to collapse
how did you get it in to boodloader mode please
HTC Touch Cruise ROM on O2 Orbit 2
Hi,
Sorry for posting on this thread which might be the wrong place but hope someone ccan help.
Can I install an HTC Cruise ROM (WM 6.1 from HTC website) on my Orbit 2 ?